1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. PaulG
    Post

    torx or allen head?

    57cj5, On my ARB covers, the supplied bolts were all 3/16" to long. Grind down the lead end of threads as necessary. I do not recommend ARB'b...
    Post by: PaulG, Apr 9, 2011 in forum: Early CJ5 and CJ6 Tech
  2. PaulG
    Post

    any body know what happend?

    If I remember correctly, the early 283's & 350 harmonic balancer were pressed on. The 327's have a center bolt torqued @60ftlbs.
    Post by: PaulG, Mar 29, 2011 in forum: Early CJ5 and CJ6 Tech
  3. PaulG
    Post

    PTO shaft for Ramsey Winch

    Mine has three shafts, two hangers and no slips, and works fine.
    Post by: PaulG, Mar 3, 2011 in forum: Early CJ5 and CJ6 Tech
  4. PaulG
    Post

    identify this trans..???

    I am running the M21, nothing like the old RC22, noise wise.
    Post by: PaulG, Feb 24, 2011 in forum: Early CJ5 and CJ6 Tech
  5. PaulG
    Post

    identify this trans..???

    I Don't know how accurate this is. Muncie 4 Speed Transmissions
    Post by: PaulG, Feb 23, 2011 in forum: Early CJ5 and CJ6 Tech
  6. PaulG
    Post

    D18

    Thanks All for your insight on this. The gears ran quietly, but knowing one is compromised will bug me. The best price I can find for Tera gears...
    Post by: PaulG, Feb 18, 2011 in forum: Early CJ5 and CJ6 Tech
  7. PaulG
    Thread

    D18

    Hi Guys, I tore down my D18, changing to twin stick. The intermediate gear has one chipped tooth and the output shaft gear shows some wear. I...
    Thread by: PaulG, Feb 18, 2011, 7 replies, in forum: Early CJ5 and CJ6 Tech
  8. PaulG
    Post

    HEI aggravation

    So if I advance it about a tooth I think I should be at about zero as it looks like its at about 15 or20 degrees after. I'll mark the housing on...
    Post by: PaulG, Jan 25, 2011 in forum: Early CJ5 and CJ6 Tech
  9. PaulG
    Post

    radiators ...can i fit it

    This is his. http://i1180.photobucket.com/albums/x411/roadworker00/SANY1300.jpg
    Post by: PaulG, Jan 22, 2011 in forum: Early CJ5 and CJ6 Tech
  10. PaulG
    Post

    Removing trans and t/c ???

    I am with Walt & Steve on pulling the engine. Freeze plugs seem to run in packs. Replace all of them.
    Post by: PaulG, Jan 20, 2011 in forum: Early CJ5 and CJ6 Tech
  11. PaulG
    Post

    vaccum timing advance

    Yes, the rotor turns half the revolutions of crankshaft, IE: 2 to1 .
    Post by: PaulG, Jan 9, 2011 in forum: Early CJ5 and CJ6 Tech
  12. PaulG
    Post

    ramsey 8000 pto winch???

    [IMG] [IMG]
    Post by: PaulG, Jan 9, 2011 in forum: Early CJ5 and CJ6 Tech
  13. PaulG
    Post

    oil pressure

    The trapped air will not let it fill to the top. Was there any oil in the filter housing? If any oil is present, I would recheck, gauge,...
    Post by: PaulG, Jan 6, 2011 in forum: Early CJ5 and CJ6 Tech
  14. PaulG
    Post

    ramsey 8000 pto winch???

    This is a Ramsey PT1-J, bolts on rear of D18 transfer case. [IMG] [IMG]
    Post by: PaulG, Jan 5, 2011 in forum: Early CJ5 and CJ6 Tech
  15. PaulG
    Post

    Buick 225 pushrod length

    So, how many thousands of an inch of lifter pre-load did you end up with ?
    Post by: PaulG, Jan 2, 2011 in forum: Early CJ5 and CJ6 Tech
  16. PaulG
    Post

    Buick 225 pushrod length

    Pre-Load on lifters should more in the range of .030 ... .060.
    Post by: PaulG, Dec 30, 2010 in forum: Early CJ5 and CJ6 Tech
  17. PaulG
    Post

    Buick 225 pushrod length

    Oiled.
    Post by: PaulG, Dec 23, 2010 in forum: Early CJ5 and CJ6 Tech
  18. PaulG
    Post

    Buick 225 pushrod length

    This is what is messing me up. Comp's pushrods for the 225. COMP Cams 7869-12 - COMP Cams High Energy Pushrods - Overview - SummitRacing.com
    Post by: PaulG, Dec 23, 2010 in forum: Early CJ5 and CJ6 Tech
  19. PaulG
    Post

    Buick 225 pushrod length

    Hi Patrick, I am not trying to make trouble, just trying to sort this out.
    Post by: PaulG, Dec 23, 2010 in forum: Early CJ5 and CJ6 Tech
  20. PaulG
    Post

    Buick 225 pushrod length

    Hmmm, ??? I went out and looked in my 1972 vintage book. It shows the rockers oiled through the head, and the rocker PR socket oiled through the PR.
    Post by: PaulG, Dec 23, 2010 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 40 Next >
Search Again
Page 1 of 2
New Posts