1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

What Did You Do To Your Jeep Today?

Discussion in 'Builds and Fabricators Forum' started by Focker, Jul 23, 2016.

  1. Jul 23, 2016
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,550
    Don't have something worthy of its own thread? Tell/show the group what you built, fixed or maintained today.

    This isn't a "Took it for a drive" thread...That belongs here - Show Us Your Jeep!
     
  2. Jul 23, 2016
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,550
    I got tired of the driver's side muffler hitting the bottom of the tub due to vibration at certain RPM's. I could have made a new bracket, but decided just to extend the existing one.
    [​IMG]

    I also checked the air pressure in all the tires and double checked the lug nut torque since having the rear wheels off a few miles ago.
     
    Dwins1, Bodhishark and tomasinator like this.
  3. Jul 23, 2016
    Rich M.

    Rich M. Shoe salesman 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Maryland
    Joined:
    Mar 23, 2008
    Messages:
    2,352
    I got this bag of snaps in the mail courtesy of Twin2 ( beer money on the way Rob, thanks!)
    IMG_20160723_194204_315-1.jpg IMG_20160723_194034_580-1.jpg
     
    Bodhishark likes this.
  4. Jul 23, 2016
    Desert Runner

    Desert Runner Member 2024 Sponsor 2022 Sponsor

    Hickory, Pa
    Joined:
    Sep 11, 2005
    Messages:
    878
    This is cool, there is a thread like this on the HRJA board that's over 520 posts and growing, I'll have to join in here too,
    I was going to do a body off clean up, (did a full restoration in 99, and 17 years has done in my POR 15 attempt at rust proofing, it's coming off in sheets) But I just am not ready to put in that much work, and money. SS doesn't kick in for 2 more years so funds are limited. So I'm just cleaning things up putting on Extends from loctite and patching rust holes

    Today I just applied the Extends. it turns the rust black then you paint over it.
    [​IMG]

    [​IMG]

    hopefully I can get 2 years out of this and then do a proper 2nd resto.
    Jay
     
  5. Jul 23, 2016
    aallison

    aallison 74 cj6, 76 cj5. Has anyone seen my screwdriver?

    Green Cove...
    Joined:
    Nov 24, 2006
    Messages:
    1,929
    Pumped up the tire on the six. It was flat from sitting and waiting patiently on me to work on her again.
     
  6. Jul 23, 2016
    3b a runnin

    3b a runnin Active Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    virginia
    Joined:
    Jan 11, 2015
    Messages:
    1,355
    drove the 3B to the gas station, filled her up, jerry can also. later retorqued the head bolts. just replaced the head gasket couple days ago. checked points gap and set the idle up a tad.
     
  7. Jul 24, 2016
    Mark Wahlster

    Mark Wahlster Member

    Silverton, OR
    Joined:
    Dec 17, 2015
    Messages:
    386
    I extended the table I am building my Tub on yesterday so today I leveled the floor section and the wheel houses on the table then I slide a sheet of 16ga that will become my new front floors under the Riser and got it squared up. I then cut back the old floor on the section of the tub that has the dash and firewall (think front floor and everything above the lower cowl sections) And I am now in the process of trying to get it all perfectly aligned so I can drill some 1/16" holes between the two layers and use them to locate my straight edge for a scribe line. Then I'll cut the new metal to match what I want to remove from the old metal. After that I will have to bend up some tunnel patches.
     
  8. Jul 24, 2016
    ca51flatty

    ca51flatty I wheeled w Charlie Hazel

    SoCal
    Joined:
    Jan 19, 2004
    Messages:
    156
    Set the throughout bearing up and installed the transmission. One item fixed and 4 more issues that need attention show up! Figures.

    VS Chassis.JPG
     
    jpflat2a and montanacj like this.
  9. Jul 24, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Veradale, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,764
    Dreamt about working on it, rather than installing this kitchen. :n:
     
    Skipjack and GraySkies like this.
  10. Jul 24, 2016
    Beach66Bum

    Beach66Bum 1966 Tuxedo Park Mark IV 2024 Sponsor

    Big Island on...
    Joined:
    Oct 30, 2015
    Messages:
    1,661
    Went for a evening cruise with the top off and the wife joined me. Had a great time cruising around the back roads. Then I did an oil change on the jeep (y)
    More cruising around for today, beautiful summer weather and blue sky.
     
  11. Jul 24, 2016
    jpflat2a

    jpflat2a what's that noise?

    Hermosa, SD
    Joined:
    Jul 30, 2003
    Messages:
    8,559
    Looked at the Jeep.
    Looked at the battery charger.
    Looked at the stuff on the hood of the Jeep.
    Looked at the stuff on the ground in front of the Jeep.
    Looked at the fridge....
    Yep, got a cold bottle of water.. and back indoors I went.
     
    PigeonsBlood, wheelie and ITLKSEZ like this.
  12. Jul 24, 2016
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,507
    Got the '49 running, ordered some lights to finish electrical before bumper builds start.

    Got the '51 close to ready for camping this year. Found a leak on the hydro clutch, trying to figure if it can wait till I do the whole pedal swap out next year...

    Worked on the wife's '66 Mustang - she wants better steering, so I ordered a Rack n Pinion swap for it from Flaming River. Get that on after fixing the mess in her drivers door and score some major Willys Points :D
     
    montanacj likes this.
  13. Jul 24, 2016
    montanacj

    montanacj Member

    Joined:
    Jul 11, 2012
    Messages:
    794
    I mounted a license plate on the 55 I found on ebay.
    It's a montana farm plate.
    It was only two bolts but I had to get the wrenches out. :)

    Edit it's centered now too.

    [​IMG]
     
    Last edited: Jul 24, 2016
    Criss, BJHitson60, ojgrsoi and 3 others like this.
  14. Jul 25, 2016
    wheelie

    wheelie beeg dummy 2024 Sponsor 2023 Sponsor

    York, PA
    Joined:
    Mar 6, 2004
    Messages:
    4,607
    been working on my Dana 27. Rebuilt a Power Lock. Had it installed with 4.88 gears. Finally got it back and now I'm putting the knuckles on. Had to grind on the balls on the ends of the housing today to clearance the button head cap screws for the knuckle stud conversion. Got both sides done this AM before it got too hot out. Then, started replacing the king pin races and bearings only to find that 1/2 of the set of NOS Timken bearings and races that I bought on eBay 3 years ago were actually old used Bower bearings put back in the Timken boxes.:mad: Todays progress ground to halt after getting one side replaced and the preload set to about 15 lbs with a fish scale. Now, I'll be waiting several days for the rest of the king pin bearings and races to show up. I've been chopped off at the knees at every turn on this project.



     
  15. Jul 25, 2016
    termin8ed

    termin8ed I didn't do it Staff Member

    Mason, MI
    Joined:
    Dec 22, 2002
    Messages:
    4,473
    Pulled the accelerator pump off the 2g last night. The metal rod seperated from the plastic housing while in the carb. Need to find another. This one was supposed to be ethanol safe...
     
  16. Jul 25, 2016
    73 cj5

    73 cj5 Not ready for the junkyard yet

    Clinton, Mississippi
    Joined:
    Jan 10, 2014
    Messages:
    2,154
    Took my engine apart again. Thinking of repainting the jeep. Red or blue? We'll see.
     
  17. Jul 25, 2016
    55_Willys_CJ5

    55_Willys_CJ5 Nephews Visit 2017 2024 Sponsor 2023 Sponsor

    Southern California
    Joined:
    Aug 4, 2015
    Messages:
    330
    While waiting on my engine to be ready at the Machine Shop. I went over to my buddy's and gave him a hand assembling his FC150. Yes, Focker, the same FC150 I teased you with a while back. :p

    We mounted the bed, fenders, tailgate, installed the rear glass and side glass in the cab. Fixed the alignment on the front cab and installed the aft cab mounts correctly. Here are some pictures:

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
    Cole King, fhoehle, ojgrsoi and 3 others like this.
  18. Jul 25, 2016
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,550
    Great progress... When will it move under it's own power?
     
  19. Jul 25, 2016
    55_Willys_CJ5

    55_Willys_CJ5 Nephews Visit 2017 2024 Sponsor 2023 Sponsor

    Southern California
    Joined:
    Aug 4, 2015
    Messages:
    330
    If all goes well hopefully in about a month or two. When we do get Melonhead, that is the FC 150's name, moving under its own power I will take a video of it and post it.
     
  20. Jul 25, 2016
    Jasontg

    Jasontg Member

    Georgia
    Joined:
    Feb 6, 2014
    Messages:
    136
    Topped off the battery, aired up the tires, put some fuel in it and let it run for a bit. One day the stars will align and I'll get it back on the road.
     
New Posts