1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by Rick

  1. Rick
    Post

    232ci-throttle Body Or Multiport Fuel-injection Upgrade

    Geez, I have a MC 2100 and love it! Four years with not so much as a hiccup.
    Post by: Rick, Sep 27, 2017 in forum: Intermediate CJ-5/6/7/8
  2. Rick
    Post

    Gas Tank Size

    Can't remember the brand of the one I used, but for my 73 it's 15 gal capacity.
    Post by: Rick, Apr 5, 2017 in forum: Intermediate CJ-5/6/7/8
  3. Rick
    Post

    1973 232ci / Pertronix Ignitor 1162a

    I have a complete kit for a jeep 6 cyl from Montgomery ward that's been around my Jeep stuff for about 10+ years. I did install a Pertronix on a...
    Post by: Rick, Feb 18, 2017 in forum: Intermediate CJ-5/6/7/8
  4. Rick
    Post

    Parking Brake Assembly

    If either JBScat or yellowjeep79 still have their parking brake assy, I'd be interested. Can't seem to see how to PM, sorry.:(
    Post by: Rick, Feb 14, 2017 in forum: Intermediate CJ-5/6/7/8
  5. Rick
    Post

    Replace Body Mounts On 72 Cj5

    I had the same problem even with new mounts. Turns out it's a common situation with the early Jeeps. It was suggested to me by member "Tim", that...
    Post by: Rick, Jan 30, 2017 in forum: Intermediate CJ-5/6/7/8
  6. Rick
    Post

    A Little Bit Of Lean

    I had the same thing and Tim suggested the factory fix of placing a 3/8" thick shim between the right hand axle spring pad and the spring. This...
    Post by: Rick, Sep 17, 2016 in forum: Intermediate CJ-5/6/7/8
  7. Rick
    Post

    I'm over it!!!

    I had a similar problem in that when my 258 was hot after running, the gas would vaporize when the engine was shut off for about 15 min. I bought...
    Post by: Rick, Aug 17, 2015 in forum: Intermediate CJ-5/6/7/8
  8. Rick
    Post

    Factory side mirror arm questions.

    I know on my '73, it's just metal to metal contact. I adjust both tensions by adjusting the bolts. This is the way it's been since I've owned it...
    Post by: Rick, Jan 8, 2015 in forum: Intermediate CJ-5/6/7/8
  9. Rick
    Post

    plug wiring

    That's correct.
    Post by: Rick, Dec 8, 2014 in forum: Intermediate CJ-5/6/7/8
  10. Rick
    Post

    help identify this bumper

    Looks pretty similar to one installed on the front of my 73 CJ that came from here... http://www.thedirtworx.com/
    Post by: Rick, Nov 3, 2014 in forum: Intermediate CJ-5/6/7/8
  11. Rick
    Post

    amc v8 4bbl intake question

    The adapter passages are tapered to make the carb bores on top blend into the ports on the manifold. If you flip the adapter over, you will mess...
    Post by: Rick, Nov 28, 2013 in forum: Intermediate CJ-5/6/7/8
  12. Rick
    Post

    amc v8 4bbl intake question

    Tim, good call on the primary positioning.:iagree:
    Post by: Rick, Nov 28, 2013 in forum: Intermediate CJ-5/6/7/8
  13. Rick
    Post

    amc v8 4bbl intake question

    This is the 650 Holley that goes on that manifold without an adapter. http://www.ebay.com/bhp/holley-650-spreadbore
    Post by: Rick, Nov 27, 2013 in forum: Intermediate CJ-5/6/7/8
  14. Rick
    Post

    Ways to Straighten Steering Wheel

    Yes, the lower is connected with splines as well. I'm just not sure if the splines have a flat spot that would prevent sliding it on at a...
    Post by: Rick, Feb 12, 2013 in forum: Intermediate CJ-5/6/7/8
  15. Rick
    Post

    Ways to Straighten Steering Wheel

    I don't see a concern with the lower bushing or washer when rotating the upper shaft and wheel, if I understand your question correctly. The horn...
    Post by: Rick, Feb 12, 2013 in forum: Intermediate CJ-5/6/7/8
New Posts