1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by 1fastsedan

  1. 1fastsedan
    Post

    1970 Cj5 Build

    slow and steady as she goes! finally getting some welding done. got the d rings installed along with the u bolt flip kit. [IMG] [IMG] [IMG]
    Post by: 1fastsedan, Apr 11, 2012 in forum: Builds and Fabricators Forum
  2. 1fastsedan
    Post

    1970 Cj5 Build

    Ok, I'm back! got married and had a baby boy, whew. now i'm ready to start working on this jeep again. I drilled out the spindle to accept these...
    Post by: 1fastsedan, Jan 30, 2012 in forum: Builds and Fabricators Forum
  3. 1fastsedan
    Post

    Tub underside finish?

    i have pondered the same idea. i also thought about "rhino lining" the whole cab. but i'm concerned about weight and looks. i didn't know that the...
    Post by: 1fastsedan, May 18, 2011 in forum: Builds and Fabricators Forum
  4. 1fastsedan
    Post

    The "You're an Idiot" restoration

    detailed, very detailed. keep up the good work
    Post by: 1fastsedan, May 18, 2011 in forum: Builds and Fabricators Forum
  5. 1fastsedan
    Post

    Finally got her on her wheels!

    super clean. nice work. show room condition!
    Post by: 1fastsedan, May 18, 2011 in forum: Builds and Fabricators Forum
  6. 1fastsedan
    Post

    My 1970 stainless steel body cj5

    the tub probably weighs around 400 lbs???. so 4% of 400 is 16lbs. i would take 16lbs over rust any day!
    Post by: 1fastsedan, May 12, 2011 in forum: Builds and Fabricators Forum
  7. 1fastsedan
    Post

    tie rods for a saginaw power steering conversion

    http://www.rockcrawler.com/techreports/bigdaddy_cj_tierod/index.asp check this site out. if you want to beef it up i suggest big daddy tie rods.
    Post by: 1fastsedan, May 11, 2011 in forum: Early CJ5 and CJ6 Tech
  8. 1fastsedan
    Post

    Tubing Bender

    www.AffordableBender.com check this out
    Post by: 1fastsedan, May 11, 2011 in forum: Builds and Fabricators Forum
  9. 1fastsedan
    Post

    My 1970 stainless steel body cj5

    how much more weight does all that stainless add? it's basically bullet proof!
    Post by: 1fastsedan, May 11, 2011 in forum: Builds and Fabricators Forum
  10. 1fastsedan
    Post

    1970 Cj5 Build

    yep, the clutch set up came like this when i bought it. i just had to make some minor adjustments to make it work. thank you. i've had so much on...
    Post by: 1fastsedan, May 5, 2011 in forum: Builds and Fabricators Forum
  11. 1fastsedan
    Post

    1970 Cj5 Build

    [IMG] [IMG] ran a some strips across the front and back of the x member. i need to unbolt it and finish welding it up.
    Post by: 1fastsedan, Jan 25, 2011 in forum: Builds and Fabricators Forum
  12. 1fastsedan
    Post

    1970 Cj5 Build

    [IMG] [IMG] [IMG] front and rear bumper welded on. this should give it some rigidity.
    Post by: 1fastsedan, Jan 25, 2011 in forum: Builds and Fabricators Forum
  13. 1fastsedan
    Post

    Herm's MC conversion

    [IMG] [IMG] lever compressed
    Post by: 1fastsedan, Jan 25, 2011 in forum: Early CJ5 and CJ6 Tech
  14. 1fastsedan
    Post

    Herm's MC conversion

    [IMG] [IMG] [IMG] [IMG] [IMG]
    Post by: 1fastsedan, Jan 25, 2011 in forum: Early CJ5 and CJ6 Tech
  15. 1fastsedan
    Post

    Herm's MC conversion

    google image "jeep master cylinder push rod"
    Post by: 1fastsedan, Jan 21, 2011 in forum: Early CJ5 and CJ6 Tech
New Posts