1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by Mark T.

  1. Mark T.
    Post

    Dana 18 Rear Output Bearing Sits Proud And Still Zero Play

    got it all back apart and reset the shaft and bearings. It naturally sits a little tighter than I expected but I got it within specs. I had no...
    Post by: Mark T., Jul 31, 2023 in forum: Early CJ5 and CJ6 Tech
  2. Mark T.
    Post

    Where To Find Parts

    This helps me soo much. I have been searching for seats for a while. Thanks! :beer:
    Post by: Mark T., Jul 24, 2023 in forum: Early CJ5 and CJ6 Tech
  3. Mark T.
    Post

    Where To Find Parts

    I think I have some that you can come over and take measurements from. Be nice to meet someone in my neck of the woods too. Send me a private...
    Post by: Mark T., Jul 24, 2023 in forum: Early CJ5 and CJ6 Tech
  4. Mark T.
    Post

    Show Us Your Jeep!

    I agree it looks right. I have a slightly different top that looks like it has a sun visor. Have you had any trouble with that Can and tire...
    Post by: Mark T., Jul 23, 2023 in forum: Builds and Fabricators Forum
  5. Mark T.
    Post

    Dana 18 Rear Output Bearing Sits Proud And Still Zero Play

    Gonna try this next. Thanks for the insight.
    Post by: Mark T., Jul 20, 2023 in forum: Early CJ5 and CJ6 Tech
  6. Mark T.
    Post

    Dana 18 Rear Output Bearing Sits Proud And Still Zero Play

    yep got so many that it is what caused me to pause and look for answers. Gonna do what Andrew suggested to see if I can get a better fit.
    Post by: Mark T., Jul 20, 2023 in forum: Early CJ5 and CJ6 Tech
  7. Mark T.
    Post

    My 1958 Cj5 "work In Progress" - Updated 12/10/2024 Roll Bar Fab On Pg.3

    Love the thread and pictures. Mine is the same year and I am starting to understand from the pictures where some stuff is supposed to go. Kind of...
    Post by: Mark T., Jul 19, 2023 in forum: Builds and Fabricators Forum
  8. Mark T.
    Thread

    Dana 18 Rear Output Bearing Sits Proud And Still Zero Play

    Hi all, I am rebuilding the Dana 18 and I have it all put back together EXCEPT for the rear bearing cap. I cannot get any play out of the shaft to...
    Thread by: Mark T., Jul 19, 2023, 17 replies, in forum: Early CJ5 and CJ6 Tech
  9. Mark T.
    Post

    How To Install Fuel Pressure Regulator And Fuel Filter. 1964 Cj5. F-134

    Thanks Rick. I was looking for a way to clean this up and make it a little easier for me to route today!
    Post by: Mark T., Jan 28, 2023 in forum: Early CJ5 and CJ6 Tech
  10. Mark T.
    Post

    Dual Action Fuel Pump Swap

    Thank you for the replies.
    Post by: Mark T., Apr 30, 2022 in forum: Early CJ5 and CJ6 Tech
  11. Mark T.
    Post

    Dual Action Fuel Pump Swap

    If I can rebuild it is there any issue with just capping off the vacuum tubes with a rubber cap?
    Post by: Mark T., Apr 25, 2022 in forum: Early CJ5 and CJ6 Tech
  12. Mark T.
    Post

    Dual Action Fuel Pump Swap

    I has just been sitting for years (10 plus) so with rebuilding everything else I thought I could rebuild it. I enjoy that sort of thing if I can...
    Post by: Mark T., Apr 25, 2022 in forum: Early CJ5 and CJ6 Tech
  13. Mark T.
    Post

    Dual Action Fuel Pump Swap

    I would be interested to know more yes.
    Post by: Mark T., Apr 17, 2022 in forum: Early CJ5 and CJ6 Tech
New Posts