1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 4
  1. S-Rage
    Post

    Are these the 11'' backing plates I need

    2 down 2 to go. Thats if I win these
    Post by: S-Rage, Feb 9, 2006 in forum: Early CJ5 and CJ6 Tech
  2. S-Rage
    Thread

    Are these the 11'' backing plates I need

    I saw these on Ebay today and wanted to know if they are what I need for my 62 CJ-5. 11'' Backing Plates
    Thread by: S-Rage, Feb 9, 2006, 10 replies, in forum: Early CJ5 and CJ6 Tech
  3. S-Rage
    Post

    New Timing cover

    Thanks for the help everyone, Lynn I don't know how you found that cam button thread I couldn't find it with the search.
    Post by: S-Rage, Jan 3, 2006 in forum: Early CJ5 and CJ6 Tech
  4. S-Rage
    Post

    New Timing cover

    Can anyone help with this
    Post by: S-Rage, Jan 3, 2006 in forum: Early CJ5 and CJ6 Tech
  5. S-Rage
    Thread

    New Timing cover

    I'm trying to locate a source for a new timing cover. Are they still available? Is there any chance I can use one from a 231. Also is there...
    Thread by: S-Rage, Jan 2, 2006, 9 replies, in forum: Early CJ5 and CJ6 Tech
  6. S-Rage
    Post

    Cost for rebuilding axles

    OK, I guess I'm going to be doing this by myself. Get ready for some stupid questions.
    Post by: S-Rage, Dec 28, 2005 in forum: Early CJ5 and CJ6 Tech
  7. S-Rage
    Post

    Cost for rebuilding axles

    How hard is this rebuild. The Jeep Rebuilders manual makes it sound like the worst part of a rebuild. Is this something I can do myself?
    Post by: S-Rage, Dec 27, 2005 in forum: Early CJ5 and CJ6 Tech
  8. S-Rage
    Post

    Cost for rebuilding axles

    Just new bearings and seals after tear down and inspection for unknown problems. Would you recommend having anything else done. I'm not using this...
    Post by: S-Rage, Dec 27, 2005 in forum: Early CJ5 and CJ6 Tech
  9. S-Rage
    Thread

    Cost for rebuilding axles

    I don't want to mess with rebuilding the axles on my Jeep and was wondering what it would cost for a shop to take care of it. I have a quote for...
    Thread by: S-Rage, Dec 27, 2005, 21 replies, in forum: Early CJ5 and CJ6 Tech
  10. S-Rage
    Post

    Rear drum removal Tool

    Will one of these work. Hub Puller Hub Puller
    Post by: S-Rage, Dec 21, 2005 in forum: Early CJ5 and CJ6 Tech
  11. S-Rage
    Thread

    Rear drum removal Tool

    I found this from a previous thread and was going to get it but I also saw that some people recommended a different one but couldn't say where...
    Thread by: S-Rage, Dec 21, 2005, 7 replies, in forum: Early CJ5 and CJ6 Tech
  12. S-Rage
    Post

    How do I tell if I have 9" or 11" drums

    So know that I know for sure that I have to upgrade the brakes does that mean that every thing from the backing plates forward is going to need to...
    Post by: S-Rage, Dec 21, 2005 in forum: Early CJ5 and CJ6 Tech
  13. S-Rage
    Post

    How do I tell if I have 9" or 11" drums

    Thanks Mcruff thats what I figured. Now I have to find those bigger backing plates.
    Post by: S-Rage, Dec 21, 2005 in forum: Early CJ5 and CJ6 Tech
  14. S-Rage
    Thread

    How do I tell if I have 9" or 11" drums

    Do you measure the inside diameter of the drums or the diameter of the backing plates. Inside diameter of my drums is 9 and the back plates...
    Thread by: S-Rage, Dec 21, 2005, 6 replies, in forum: Early CJ5 and CJ6 Tech
  15. S-Rage
    Post

    Rear Cross-member?

    Looks like the same holes as mine. I have a swing out spare tire carrier that yours might have had at one time.
    Post by: S-Rage, Dec 14, 2005 in forum: Early CJ5 and CJ6 Tech
  16. S-Rage
    Post

    Help on disassembly of front hub et.al.

    I'm in the process of doing this as well. I used two screw drivers to get the snap ring out. The big nuts use a 2 inch hex which I got from...
    Post by: S-Rage, Dec 13, 2005 in forum: Early CJ5 and CJ6 Tech
  17. S-Rage
    Post

    Deluxe overhaul kit from Kanter

    Ok let me rephrase my comment I want to do whatever it takes, within reason, to make this engine run good for 5yrs +. The only reason I'm doing...
    Post by: S-Rage, Dec 7, 2005 in forum: Early CJ5 and CJ6 Tech
  18. S-Rage
    Post

    Deluxe overhaul kit from Kanter

    Will all machine shops be able to install seat valves. I think I'll go ahead and get them done since I'm trying to do whatever it takes to make...
    Post by: S-Rage, Dec 7, 2005 in forum: Early CJ5 and CJ6 Tech
  19. S-Rage
    Post

    Deluxe overhaul kit from Kanter

    Could someone post pics of a hardened exhaust valve seat and tell me what the advantages of these are. Thanks
    Post by: S-Rage, Dec 6, 2005 in forum: Early CJ5 and CJ6 Tech
  20. S-Rage
    Post

    Deluxe overhaul kit from Kanter

    Here is a picture I took of the broken/chipped rocker arm. [IMG]
    Post by: S-Rage, Dec 6, 2005 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 77 Next >
Search Again
Page 1 of 4
New Posts