1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by BESRK

  1. BESRK
    Post

    Greenies getting 1 tons

    Nice build! Brings back memories of my old CJ5.. One suggestion.. run 42s!!
    Post by: BESRK, Jan 20, 2008 in forum: Builds and Fabricators Forum
  2. BESRK
    Post

    Holley Projection Help

    Check to make sure the Throttle Position Sensor is set to the proper voltage. I can't remember what it is off the top of my head but it's in the...
    Post by: BESRK, Jan 13, 2005 in forum: Intermediate CJ-5/6/7/8
  3. BESRK
    Post

    Power steering swap on a '73

    Shouldn't be too hard to find a mount. Check on eBay under "jeep steering box" . I saw some stock mounts and some of the hefty aftermarket mounts...
    Post by: BESRK, Oct 22, 2004 in forum: Intermediate CJ-5/6/7/8
  4. BESRK
    Post

    Which leaf springs

    I used RE 1.5" Extreme Duty Reverse Eye Wrangler SOA springs. They allow me to easily clear 35" TSLs. Love 'em. They flex well, ride well, and...
    Post by: BESRK, Oct 2, 2004 in forum: Early CJ5 and CJ6 Tech
  5. BESRK
    Post

    metal thickness

    I would use 3/4"x2" or 1"x2" flat stock drilled with about a 1" hole for the shackle.
    Post by: BESRK, Oct 2, 2004 in forum: Early CJ5 and CJ6 Tech
  6. BESRK
    Post

    '75 CJ5 Suspension conversion or repair?

    Depending on your welding/fabricating skill I'd opt for the YJ stuff. You can get later CJ rear spring/shackle hangers and use those to get the...
    Post by: BESRK, Sep 30, 2004 in forum: Intermediate CJ-5/6/7/8
  7. BESRK
    Post

    Pilot Bushing Removal

    I like the soggy toilet paper idea. I hate having to clean the grease up afterwards. Should I put on gloves before I fish the paper out of the...
    Post by: BESRK, Sep 29, 2004 in forum: Early CJ5 and CJ6 Tech
  8. BESRK
    Post

    Heim Joints

    Grade 8 bolts are stronger than grade 5 bolts in both shear and tension. They'll also bend before they break (depending on the situation). Put a...
    Post by: BESRK, Sep 29, 2004 in forum: Early CJ5 and CJ6 Tech
  9. BESRK
    Post

    Axle swap....

    I'd recommend a Waggy front and a Scout rear. If you can pickup a pre 77 (if I remember correctly) Waggy front, it'll come with the smaller...
    Post by: BESRK, Sep 28, 2004 in forum: Intermediate CJ-5/6/7/8
  10. BESRK
    Post

    Heim Joints

    Yep, I use 3/4"x3/4" joints and was able to pickup grade 8 bolts, nuts and washers from Northern..but I'm sure any fastener shop would have what...
    Post by: BESRK, Sep 28, 2004 in forum: Early CJ5 and CJ6 Tech
  11. BESRK
    Post

    Heim Joints

    I've been running heims for over 2 years now and love 'em. One thing I recommend however, is using a safety washer under the bolt head to prevent...
    Post by: BESRK, Sep 27, 2004 in forum: Early CJ5 and CJ6 Tech
  12. BESRK
    Thread

    Holley Projection TPS replacement

    Anybody know what GM TPS will interchange with the TPS on a Holley Projection TBI system.. specifically the 502-20 system (670 cfm)? I'd like to...
    Thread by: BESRK, Aug 14, 2004, 0 replies, in forum: Intermediate CJ-5/6/7/8
  13. BESRK
    Post

    Ford Clutch & Chevy Pressure Plate?

    I mated my Ford NP435 to my Chevy 350 with a Chevy PP and Ford disk (both were 11"). I also had the front bearing retainer snout turned down so I...
    Post by: BESRK, Jul 22, 2004 in forum: Early CJ5 and CJ6 Tech
  14. BESRK
    Post

    11" drum brake hardware question

    termin8ed if you're interested, I think I have Jeep 11" backing plates (with wheel cylinders still attached, drums and maybe some of the hardware...
    Post by: BESRK, Jul 22, 2004 in forum: Early CJ5 and CJ6 Tech
New Posts