1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by timo2

  1. timo2
    Post

    Interesting welded frame additions, what in the world are these for?

    Id guess it lived as a trailered off-road warrior, or was a truckers personal vehicle and was trailered to job sites a lot. Or it liked to fly,...
    Post by: timo2, Aug 25, 2015 in forum: Intermediate CJ-5/6/7/8
  2. timo2
    Post

    Where do I find tail light lenses?

    I have two used intact ones, different styles. One says 76, the other 75....one is larger in diameter than the other.
    Post by: timo2, Aug 19, 2015 in forum: Intermediate CJ-5/6/7/8
  3. timo2
    Post

    No Brakes!

    I have a '73 which appears to have a valve. I suspect adding one is a good idea...
    Post by: timo2, Aug 8, 2015 in forum: Intermediate CJ-5/6/7/8
  4. timo2
    Post

    74 Frame Dimensions

    That's what a '73 measures....total (edit) length 54"
    Post by: timo2, Aug 8, 2015 in forum: Intermediate CJ-5/6/7/8
  5. timo2
    Post

    One bbl vs 2 bbl '73 258 intake

    Thanks Tim, that has been my experience with headers. I'm really not considering them, just that it was available with a one bbl carter intake...
    Post by: timo2, Aug 6, 2015 in forum: Intermediate CJ-5/6/7/8
  6. timo2
    Thread

    One bbl vs 2 bbl '73 258 intake

    Since I need a new exhaust manifold (mine was cracked before it sold to original owner in 1974, and was welded by dealer. Weld failed, jeep has 44...
    Thread by: timo2, Aug 6, 2015, 4 replies, in forum: Intermediate CJ-5/6/7/8
  7. timo2
    Post

    No Brakes!

    Didn't see whether you have PB booster, but sometimes it can draw fluid out out o the MC, under vacuum, very quickly. I agree, ten years is way...
    Post by: timo2, Aug 5, 2015 in forum: Intermediate CJ-5/6/7/8
  8. timo2
    Post

    Parts CJ5 Jeep

    I'd venture a guess bent axle shaft, Grif...i would be less concerned about worn spiders or side gears. They can take quite a bit of wear.
    Post by: timo2, Aug 3, 2015 in forum: Intermediate CJ-5/6/7/8
  9. timo2
    Post

    Parts CJ5 Jeep

    He was (Over)pricing the parts separately at $300 each axle, TC, trans, etc. I was concerned because of the frame damage, the springs were...
    Post by: timo2, Aug 2, 2015 in forum: Intermediate CJ-5/6/7/8
  10. timo2
    Post

    Rebuilt engine no compression

    Also reduces emissivity, keeping intake cooler. theoretically, and subjective anecdotes...probably has some, perhaps measurable, significance
    Post by: timo2, Jul 27, 2015 in forum: Intermediate CJ-5/6/7/8
  11. timo2
    Post

    Front end slight wobble

    Tires probably require truing. May well be, as mentioned above, slight out of round condition. If you have a spare, start by replacing each one at...
    Post by: timo2, Jul 15, 2015 in forum: Intermediate CJ-5/6/7/8
  12. timo2
    Post

    Rebuilt engine no compression

    Old thread resurrected? How long is this build lol? I do not believe the OHV 304 is zero interference engine. Valves would not contact pistons...
    Post by: timo2, Jul 7, 2015 in forum: Intermediate CJ-5/6/7/8
  13. timo2
    Post

    Toe in or out

    According to the alignment sheet, OP does have about a half degree more left camber. Not enough to visualize...not enough to be a problem. Pete...
    Post by: timo2, Jul 3, 2015 in forum: Intermediate CJ-5/6/7/8
  14. timo2
    Post

    Toe in or out

    Given rear toe out in addition to too little front toe in will give you lots of wander. And don't worry bein' a dick. You can't be near as big a...
    Post by: timo2, Jul 3, 2015 in forum: Intermediate CJ-5/6/7/8
New Posts