1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by endl

  1. endl
    Thread

    Floor replacement/fabrication pictures.

    Anyone have any good pictures their replacement floors? Especially where the floor meets the tunnel area. Trying to deceide the best way to mate...
    Thread by: endl, Jan 22, 2010, 1 replies, in forum: Builds and Fabricators Forum
  2. endl
    Post

    What size bead roller die for rear floor???

    We started in the middle. We marked out the beads using a sharpie so we had a big line to follow then would roll from one end to the other...
    Post by: endl, Jan 22, 2010 in forum: Builds and Fabricators Forum
  3. endl
    Post

    What size bead roller die for rear floor???

    Actually panel did "oil can" a bit. I will install the new hat channels then lay the new panel in the floor and then put sand bags, brake drums...
    Post by: endl, Jan 8, 2010 in forum: Builds and Fabricators Forum
  4. endl
    Post

    What size bead roller die for rear floor???

    Ok center to center bead dims are 4" and basically it is 36" from inside FW to FW. New floor from a distance not too bad looking. [IMG]...
    Post by: endl, Jan 5, 2010 in forum: Builds and Fabricators Forum
  5. endl
    Post

    What size bead roller die for rear floor???

    I actually rolled mine last night! My orginal floor had 7/8 to 15/16 wide beads and they are rounded. We only had a 5/8 roller bead and it was...
    Post by: endl, Jan 4, 2010 in forum: Builds and Fabricators Forum
  6. endl
    Post

    Replacing Ball joints

    Ok got them. I got out the BFH and they fell right out. I did shoot them up with PB and let them sit all night so that might have helped out also.
    Post by: endl, Jan 1, 2010 in forum: Intermediate CJ-5/6/7/8
  7. endl
    Post

    Replacing Ball joints

    Ok I had a great idea of looking at the new part.R) So I have a better understanding of how the seat sits on the BJ. It has a slit in the seat...
    Post by: endl, Dec 30, 2009 in forum: Intermediate CJ-5/6/7/8
  8. endl
    Post

    Replacing Ball joints

    Yeah thats the way I read it but I dont understand if the ball joint stud is threaded and the yoke is threaded and the ball joint seat is threaded...
    Post by: endl, Dec 30, 2009 in forum: Intermediate CJ-5/6/7/8
  9. endl
    Post

    Replacing Ball joints

    ????????? Huh? So that nut down inside the yoke in the last picture has to come out first or it does not matter? Yes that is the top ball joint.
    Post by: endl, Dec 30, 2009 in forum: Intermediate CJ-5/6/7/8
  10. endl
    Post

    Replacing Ball joints

    Ok so is this correct? Does not seem to be moving any. [IMG] [IMG] We are sure this nut inside the top of the yoke does not need to come...
    Post by: endl, Dec 30, 2009 in forum: Intermediate CJ-5/6/7/8
  11. endl
    Post

    Replacing Ball joints

    So once you have the spindles off, axles out nuts loose you just take the ball joint seperator and hammer into place until the ball joits...
    Post by: endl, Dec 29, 2009 in forum: Intermediate CJ-5/6/7/8
  12. endl
    Post

    11" backing plate question

    Ok thanks Nick. I did not really pay attention to the center hole as I was just holding it up against the backing plate looking at the mounting...
    Post by: endl, Dec 29, 2009 in forum: Early CJ5 and CJ6 Tech
  13. endl
    Post

    11" backing plate question

    Did you ever get a chance to get a picture of this? Also when using the 11" front plates I notice not all the holes line up with my Dana 44...
    Post by: endl, Dec 28, 2009 in forum: Early CJ5 and CJ6 Tech
  14. endl
    Post

    Dana 44 bearing retaining ring removal

    Ok, I acutall found the service manual last night on oljeep.com. It says to press the bearing retainer and bearing on at the same time. But I...
    Post by: endl, Dec 28, 2009 in forum: Intermediate CJ-5/6/7/8
New Posts