1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by grayrider

  1. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Finally after a kitchen project delay..... I]have progress again on my jeep project. Manual steering box install from 79 jeep.... Thanks to mcruff...
    Post by: grayrider, Mar 26, 2011 in forum: Builds and Fabricators Forum
  2. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Finally after a kitchen project delay..... I]have progress again on my jeep project. Manual steering box install from 79 jeep.... Thanks to mcruff...
    Post by: grayrider, Mar 26, 2011 in forum: Builds and Fabricators Forum
  3. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    [IMG][/IMG] [IMG][/IMG]e [IMG][/IMG] Finally have something to post again. Rebuilt carburetor, Put body on frame. Have some great looking...
    Post by: grayrider, Oct 4, 2010 in forum: Builds and Fabricators Forum
  4. grayrider
    Post

    F134 Rebuild in Michigan

    I had many engines done in kalamazoo michigan. The napa on centre street does a fantastic job. I believe the gentlemans name is tom. Cleanest shop...
    Post by: grayrider, Jul 8, 2010 in forum: Early CJ5 and CJ6 Tech
  5. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    [IMG][/IMG] Did a lot this weekend . Rear drive line in. Just need the front propeller shaft and the drive line will be complete....
    Post by: grayrider, Apr 25, 2010 in forum: Builds and Fabricators Forum
  6. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Made alot of progress this weekend. Transmission in and boxed in the frame for saginaw steering.\[IMG][/IMG][/IMG] [IMG][/IMG] [IMG][/IMG]...
    Post by: grayrider, Apr 25, 2010 in forum: Builds and Fabricators Forum
  7. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Well I checked it with the old one..... It looked the same diameter.....Did not slip it over the shaft.....Now you have me wondering
    Post by: grayrider, Apr 20, 2010 in forum: Builds and Fabricators Forum
  8. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Why is it you never get as much done as you plan on the weekend. Oh well It's starting to look like an engine. [IMG][/IMG] [IMG][/IMG] I have a...
    Post by: grayrider, Apr 19, 2010 in forum: Builds and Fabricators Forum
  9. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    I used the grease and the dowel and was able to pop the pilot bearing out and placed the new one. After that the clutch and pressure plate went on...
    Post by: grayrider, Apr 11, 2010 in forum: Builds and Fabricators Forum
  10. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    [IMG][/IMG] Well starting to put drive line together. It looks a lot better then it did. Have a question. How important is it to change the pilot...
    Post by: grayrider, Apr 10, 2010 in forum: Builds and Fabricators Forum
  11. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Finished painting the engine except for the timing cover. Also have rebuilt transfer case and mated it to the t-86. [IMG][/IMG] [IMG][/IMG]...
    Post by: grayrider, Mar 23, 2010 in forum: Builds and Fabricators Forum
  12. grayrider
    Post

    1966 cj5 frame up rebuild slow progress

    Getting closer.....engine almost together[IMG][/URL][/IMG][IMG][/URL][/IMG Sealed power rings were great. The hasting rings must have been...
    Post by: grayrider, Mar 14, 2010 in forum: Builds and Fabricators Forum
  13. grayrider
    Post

    Piston ring suggestion?

    Ordered some sealed powered rings. They will be in Monday. I'll pick them up Friday on my day off. And I'll try again. I returned the other rings...
    Post by: grayrider, Mar 5, 2010 in forum: Early CJ5 and CJ6 Tech
  14. grayrider
    Post

    Piston ring suggestion?

    They are hasting rings. I did put the compression ring in the cylinder and there is a gap. The oil ring will not go in the cylinder. I have taken...
    Post by: grayrider, Mar 5, 2010 in forum: Early CJ5 and CJ6 Tech
  15. grayrider
    Thread

    Piston ring suggestion?

    Rebuilding the buick 225, the Dauntless. I tried fitting the rings I purchased at auto value. The top two rings fit okay but the oil ring were to...
    Thread by: grayrider, Mar 4, 2010, 6 replies, in forum: Early CJ5 and CJ6 Tech
New Posts