1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by sheddiggs

  1. sheddiggs
    Post

    Rookie Welder Advice

    Tank is dropped, fenders off, bolts chopped, and tool box removed, now I'm ready to put her up on 4x4 blocks. Before busting the welder out and...
    Post by: sheddiggs, Apr 19, 2013 in forum: Intermediate CJ-5/6/7/8
  2. sheddiggs
    Post

    NUTS...Dry for a day!

    I did straighten her up. The seep is just enough to be annoying.
    Post by: sheddiggs, Mar 28, 2013 in forum: Intermediate CJ-5/6/7/8
  3. sheddiggs
    Post

    NUTS...Dry for a day!

    Thanks for the heads up! I'll give Auto zone a try.
    Post by: sheddiggs, Mar 28, 2013 in forum: Intermediate CJ-5/6/7/8
  4. sheddiggs
    Thread

    NUTS...Dry for a day!

    So after swapping out winches and getting rid of one leak, I couldn't help but eliminate a couple of others that'd been bothering me. Knocked...
    Thread by: sheddiggs, Mar 27, 2013, 6 replies, in forum: Intermediate CJ-5/6/7/8
  5. sheddiggs
    Post

    RMS Advice

    Success! I pulled the upper I'd been fighting and opened the other rms box. Looking at the two side by side, I realized the problem. The one...
    Post by: sheddiggs, Mar 24, 2013 in forum: Intermediate CJ-5/6/7/8
  6. sheddiggs
    Post

    RMS Advice

    Alright, the lip of the seal is facing the front, I'm doing the old in-out and have made some headway. Now I'm hung up 3/4 of the way in.
    Post by: sheddiggs, Mar 24, 2013 in forum: Intermediate CJ-5/6/7/8
  7. sheddiggs
    Post

    RMS Advice

    Thanks, I'll try the ol' in-out tomorrow.
    Post by: sheddiggs, Mar 24, 2013 in forum: Intermediate CJ-5/6/7/8
  8. sheddiggs
    Post

    RMS Advice

    Thanks, I'll try the back and forth tomorrow.
    Post by: sheddiggs, Mar 24, 2013 in forum: Intermediate CJ-5/6/7/8
  9. sheddiggs
    Thread

    RMS Advice

    I've run into a problem getting the top of the rms in. The old one came out easy, the new one isn't wanting to go in very far(about halfway.)...
    Thread by: sheddiggs, Mar 23, 2013, 9 replies, in forum: Intermediate CJ-5/6/7/8
  10. sheddiggs
    Post

    RMS re-seal today. Any input?

    I've got a similar problem getting the top of the rms in. The old one came out easy, the new one not so much. I've followed all advice, she's...
    Post by: sheddiggs, Mar 23, 2013 in forum: Intermediate CJ-5/6/7/8
  11. sheddiggs
    Post

    Pic request- ramset PTO winch data plates

    i snapped a couple of shots of my Ramsey MX200R last night while in the garage. Do you have an email address I can send these shots to? I've...
    Post by: sheddiggs, Mar 23, 2013 in forum: Early Jeep Restoration and Research
  12. sheddiggs
    Post

    Safety Issue?

    So I ended up with one bolt in each spring hanger. The easy part was drilling out one of the 3/8" holes in the hangers, then it was a contortion...
    Post by: sheddiggs, Mar 21, 2013 in forum: Intermediate CJ-5/6/7/8
  13. sheddiggs
    Post

    Safety Issue?

    Thanks, I'm glad there's enough flex in those springs to move 'em around, I'm looking for the easiest way to get this done. It's just something...
    Post by: sheddiggs, Mar 17, 2013 in forum: Intermediate CJ-5/6/7/8
New Posts