1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by burnzee

  1. burnzee
    Post

    T14 shiftlever boot

    Thanks for the info. I have bought from Walcks, but missed that they have this boot. My dimensions are slightly different, but it's pretty...
    Post by: burnzee, Jun 25, 2013 in forum: Early CJ5 and CJ6 Tech
  2. burnzee
    Post

    T14 shiftlever boot

    That's the one. Goes around to keep out the elements.
    Post by: burnzee, Jun 25, 2013 in forum: Early CJ5 and CJ6 Tech
  3. burnzee
    Thread

    T14 shiftlever boot

    Anyone have a source for a shift lever boot for a T14 bellhousing? Thanks
    Thread by: burnzee, Jun 25, 2013, 4 replies, in forum: Early CJ5 and CJ6 Tech
  4. burnzee
    Post

    backfire on rebuilt 225 engine

    Well, I'm still waiting on the new cap and rotor since I had to special order them. Won't get until at least Wednesday. I haven't had a...
    Post by: burnzee, Jun 8, 2009 in forum: Early CJ5 and CJ6 Tech
  5. burnzee
    Post

    backfire on rebuilt 225 engine

    Thanks Patrick, Knowing what you've done right, helps one determine what you've done wrong.
    Post by: burnzee, Jun 7, 2009 in forum: Early CJ5 and CJ6 Tech
  6. burnzee
    Post

    backfire on rebuilt 225 engine

    Yes, I've checked the plug wires about a dozen times. I've even checked them under supervision. Engine @ TDC #1, distributor installed with...
    Post by: burnzee, Jun 7, 2009 in forum: Early CJ5 and CJ6 Tech
  7. burnzee
    Post

    backfire on rebuilt 225 engine

    Thanks for the responses. I will go ahead and replace the rotor and cap. I have already replaced the condenser, coil, and ballast resistor. I...
    Post by: burnzee, Jun 6, 2009 in forum: Early CJ5 and CJ6 Tech
  8. burnzee
    Thread

    backfire on rebuilt 225 engine

    Hi, I'm having trouble getting my newly rebuilt engine to run correctly. Everything on it is new, with the exception of the carb (it had no carb...
    Thread by: burnzee, Jun 5, 2009, 33 replies, in forum: Early CJ5 and CJ6 Tech
  9. burnzee
    Post

    Timing prior to start 225

    Good info, It makes since to rotate engine to 5 BTDC then rotate dist. until point just open, since 5 BTDC is what you are shooting for with the...
    Post by: burnzee, May 30, 2009 in forum: Early CJ5 and CJ6 Tech
  10. burnzee
    Thread

    Timing prior to start 225

    Hi all, I have another question about what to do prior to starting a rebuilt engine for the first time. Timing. Currently, I have the engine at...
    Thread by: burnzee, May 29, 2009, 4 replies, in forum: Early CJ5 and CJ6 Tech
  11. burnzee
    Post

    Rebuild kit for Dauntless 225 - where?

    I got my gasket kit, and new clutch, from Autozone. I let the machine shop purchase the new pistons, rings, and bearings.
    Post by: burnzee, Mar 31, 2009 in forum: Early CJ5 and CJ6 Tech
  12. burnzee
    Post

    225 preprime before start

    Thanks so much. (I usually worry about the simple things.
    Post by: burnzee, Mar 19, 2009 in forum: Flat Fender Tech