1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by birddog

  1. birddog
    Post

    Puff of blue smoke on start up: questions

    I agree-definately valve seals. I wouldn't worry till it becomes excessive or constant. A little on start-up is fine. Just as a side note, alot of...
    Post by: birddog, Apr 10, 2007 in forum: Intermediate CJ-5/6/7/8
  2. birddog
    Post

    33 inch NDTs?

    I bought the Denmans from the local tire place. I am not sure where the guy got them from. I know it took it a while to get them though. He got...
    Post by: birddog, Apr 9, 2007 in forum: Early CJ5 and CJ6 Tech
  3. birddog
    Post

    33 inch NDTs?

    I am not trying to rock the boat on the NDT tire size issue here but I have a set of 9.00 x 16 NDTs in the garage that I was going to run on my 93...
    Post by: birddog, Apr 8, 2007 in forum: Early CJ5 and CJ6 Tech
  4. birddog
    Thread

    Decking a 304 block?

    Does anybody know how many thousandths I can safely take of a 304 when decking the block? Also does anybody know how thick head gaskets are? I was...
    Thread by: birddog, Apr 5, 2007, 3 replies, in forum: Intermediate CJ-5/6/7/8
  5. birddog
    Thread

    Performance 304

    So my oil pump went out in my 304 and I have spun a crankshaft bearing--just my usual luck. Anybody have any suggestions on where to get a good...
    Thread by: birddog, Feb 27, 2007, 23 replies, in forum: Intermediate CJ-5/6/7/8
  6. birddog
    Post

    Pilot Bushing

    Have you tried a pilot bushing puller? I am assuming that what is left of your bushing is just kind of seized to your crank? If you haven't used a...
    Post by: birddog, Feb 26, 2007 in forum: Intermediate CJ-5/6/7/8
  7. birddog
    Thread

    carb adjustment

    I just bought a reman 2100 motorcraft for my 75 cj-5 with a 304. I put it on and the jeep cranks and runs but the carb obviously needs adjustment....
    Thread by: birddog, Feb 20, 2007, 2 replies, in forum: Intermediate CJ-5/6/7/8
  8. birddog
    Post

    i need help fast

    I just rewired mine about 3 wks ago. Its pretty simple, here's a link to the website I used:...
    Post by: birddog, Feb 19, 2007 in forum: Intermediate CJ-5/6/7/8
  9. birddog
    Post

    Winch Cable Question

    I had a Warn xd 9000 on my last wrangler and replaced the cable. I just went to the local hardware store and bought 125' of 5/16" galvanized...
    Post by: birddog, Feb 15, 2007 in forum: Early CJ5 and CJ6 Tech
  10. birddog
    Post

    Drawbar

    Its been a while (about 5 years) but I remember seeing one in the Leon Rosser catalog and I think it was mfg by Kayline. I would also suspect that...
    Post by: birddog, Feb 15, 2007 in forum: Early Jeep Restoration and Research
  11. birddog
    Post

    New member with engine and windshield hinge question.

    Thanks for the input fellas. I think I am just going to use the cut-off wheel and cut the windshield frame because I had to replace it anyway. On...
    Post by: birddog, Feb 14, 2007 in forum: Intermediate CJ-5/6/7/8
  12. birddog
    Post

    Transmission Flush

    All answers stated by other members were good. I might suggest removing the shift tower on the top of the tranny so you can get better access to...
    Post by: birddog, Feb 13, 2007 in forum: Early CJ5 and CJ6 Tech
New Posts