1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by Turk P

  1. Turk P
    Post

    Nellers CJ5 Build

    The wheels of progress around my place have been turning pretty slow lately. I was able to get the sheet metal cut and bent to replace both...
    Post by: Turk P, Jan 19, 2014 in forum: Builds and Fabricators Forum
  2. Turk P
    Post

    Rotisserie

    Johns1967CJ5, I know it's hard to see in the pic of my Wagon body, the sawhorses have cable crossbraces on them. Also I think that if one was...
    Post by: Turk P, Jan 17, 2014 in forum: Builds and Fabricators Forum
  3. Turk P
    Post

    Hole ID

    Great. Thanks guys.
    Post by: Turk P, Jan 13, 2014 in forum: Early CJ5 and CJ6 Tech
  4. Turk P
    Post

    Rotisserie

    Thanks everyone for your help and suggestions. I would love to build a rotisserie but I downsized from a 1200sq.ft. shop to a cramped two car...
    Post by: Turk P, Jan 13, 2014 in forum: Builds and Fabricators Forum
  5. Turk P
    Post

    Rotisserie

    Yes, your right. I'm located in Las Vegas, NV Steve
    Post by: Turk P, Jan 13, 2014 in forum: Builds and Fabricators Forum
  6. Turk P
    Thread

    Rotisserie

    It's time to replace the floors on the CJ and I have read about how great Tommy rotisserie was. My concern is what do I do after I'm done with it....
    Thread by: Turk P, Jan 12, 2014, 20 replies, in forum: Builds and Fabricators Forum
  7. Turk P
    Thread

    Hole ID

    Can someone tell me what the holes on my 68' windshield are for? I don't want to weld them up if they are stock and serve a purpose. There are two...
    Thread by: Turk P, Jan 12, 2014, 5 replies, in forum: Early CJ5 and CJ6 Tech
  8. Turk P
    Post

    My 67 CJ5 build

    That's good to hear about the rotisserie. I'm going to give it a try for my tub. I look at a thread that Pielut posted about a home made...
    Post by: Turk P, Jan 11, 2014 in forum: Builds and Fabricators Forum
  9. Turk P
    Post

    My 67 CJ5 build

    Looking good. I've used POR15 and had great results. How did your redneck rotisserie workout for working with the frame? I'm getting ready to cut...
    Post by: Turk P, Jan 10, 2014 in forum: Builds and Fabricators Forum
  10. Turk P
    Post

    Building my 66 CJ6 to look capable of things it will never do

    Welcome to the forum, Here is a pic of a Wagoneer D44 next to a 14 bolt. Not the best pic to show the difference but it's a huge difference...
    Post by: Turk P, Jan 10, 2014 in forum: Builds and Fabricators Forum
  11. Turk P
    Post

    Planning My Build

    I took some measurements of my CJ to help you with your build. These measurements are with the weight of the frame, engine,trans and tub on the...
    Post by: Turk P, Jan 7, 2014 in forum: Builds and Fabricators Forum
  12. Turk P
    Post

    Nellers CJ5 Build

    tarry99, your inbox is full so I couldn't PM you. My problem is I get impatient. :( With my OA rig I can easily weld up a long flat and thin...
    Post by: Turk P, Jan 7, 2014 in forum: Builds and Fabricators Forum
  13. Turk P
    Post

    Nellers CJ5 Build

    For most projects I will mig weld it. In this case where it's 18ga steel that is dead flat, about a 5' long weld and no way to get behind it to...
    Post by: Turk P, Jan 6, 2014 in forum: Builds and Fabricators Forum
New Posts