1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

1970 Jeep Rebuild

Discussion in 'Builds and Fabricators Forum' started by Rozcoking23, Feb 8, 2011.

  1. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    My daughter test fitting the seats:
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    Jeep moving on its own:
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    I finished the wheel well notch, Re-installed old roll bar until I get my tubing bender,So I can make new one. mounted the drivers seat. All wiring is done. I shot the fenders and hood, just need to color sand and buff then i can install. I still have tail gate to finish and the glove box door. I need to measure for shocks and order those. Its getting close!
     
  2. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Once its running I need to taketo muffler shop and have new mufflers installed.
     
  3. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Finished the drivers side wheel well notch:
    [​IMG]
    ...and the passenger side:
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  4. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Fabricated the seat mounts:
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
     
  5. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    The passenger side folds up far enough to allow access to the tool box under it.....I also can remove passenger side by pulling pins. i used the original latch to secure the seat when in position.
     
  6. PieLut

    PieLut Member

    Looking good Rob! Simple and clean design.
     
  7. Warloch

    Warloch Did you say Flattie??? Staff Member

    PRP Seats?

    Hope your jeep was level too :D Don't ask how my son did his like that...
     
  8. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Thank you!!!
     
  9. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Corbeau JP extra wide seats

     
  10. rons75

    rons75 Member

    BEAUTIFUL Jeep!! Only 2 question, whats your address, and you ready to start on mine??/ lol
     
  11. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Close to being finished. Just need to finish the tail gate and some misc items:
    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]
    Fenders and hood before installing:
    [​IMG]
    [​IMG]
     
  12. wheelie

    wheelie beeg dummy 2024 Sponsor 2023 Sponsor

    That's beautiful. Love the color. And the seats frames are nicely done. Great job!
     
  13. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Thank you, the color is from a 2013 Corevette.
     
  14. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    It's hard to tell from the pictures but the black in the middle of the hood is actually carbon fiber buried in clear. I'll try to get better pics in the sun where it shows up.
     
  15. 73 cj5

    73 cj5 Not ready for the junkyard yet

    I like that color too. Beautiful Jeep.
     
  16. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Thank you
     
  17. 1967 CJ5A

    1967 CJ5A Mike 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Where did you get the chrome stuff like the windshield and hood hinges? Is that custom plated?
     
  18. tarry99

    tarry99 Member

    Very Nice..............It's going to be real tough taking that Hunting again...........at least until you get the first few scratch's in it!
     
  19. uncamonkey

    uncamonkey Member

    It's always an interesting experince to put the first scratch in a vehicle. Years ago a roomate stomped into the house, sucked down a beer. Threw the bottle aginst the wall so we had a bit of glass to clean up. He smacked his 2 week old Toyota PU into his 1964 Ford PU. The next day he could see the humor in it. OK, no worries about scratches now.
     
  20. 47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    jeep is gorgeous.