1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. tjg358
    Post

    69 soft top with bows???

    Being a former Bestop Employee I can say that the Tiger Top and Super Top both use the same bows. The tube or extrusions use around the doors vary...
    Post by: tjg358, Dec 11, 2008 in forum: Early CJ5 and CJ6 Tech
  2. tjg358
    Post

    Another axle question thread

    What years did waggies have narrow trac axels?
    Post by: tjg358, Dec 11, 2008 in forum: Early CJ5 and CJ6 Tech
  3. tjg358
    Post

    holley 470 truck avenger

    I have one on mine,225, Offy 360, TA 470, love it so far. Haven't had any issues so far. I live in Colorado and mountains are no problems for this...
    Post by: tjg358, Dec 31, 2007 in forum: Early CJ5 and CJ6 Tech
  4. tjg358
    Post

    anyone running a holley street avenger carb?

    470 TA on mine, love it so far.
    Post by: tjg358, Nov 11, 2007 in forum: Early CJ5 and CJ6 Tech
  5. tjg358
    Post

    1971 Jeep Gear problem

    I had similar noise few years back, mine was intermediate shaft and bearings.
    Post by: tjg358, Oct 6, 2007 in forum: Early CJ5 and CJ6 Tech
  6. tjg358
    Post

    Supertop For M38a1

    Super Top used a Belt Rail System. It consists of am L shaped rail the bolts to the tub, You then hook a plastic retainer in it that is sewn to...
    Post by: tjg358, Aug 17, 2007 in forum: Early CJ5 and CJ6 Tech
  7. tjg358
    Post

    Another power steering question

    Mine steers soooooo easy I am thinking of toning it down somehow. Does anyone know how to reduce the pump pressure.
    Post by: tjg358, Jul 25, 2007 in forum: Intermediate CJ-5/6/7/8
  8. tjg358
    Post

    Fresh from the powder coater

    Most powders are polyester of some sort, the powder takes an electostatic charge (natuarlly want to go to ground). Your metal parts are grounded...
    Post by: tjg358, May 25, 2007 in forum: Builds and Fabricators Forum
  9. tjg358
    Post

    4 wire Wipers

    thanks for the info. A buddy of mine has a 4 wire motor and will let me try it for size.
    Post by: tjg358, May 14, 2007 in forum: Early CJ5 and CJ6 Tech
  10. tjg358
    Thread

    4 wire Wipers

    Has anyone tried to put delay wipers on their jeep? I have a 70 CJ, as far as I know I would need a 4 wire wiper motor and I dont know if one...
    Thread by: tjg358, May 9, 2007, 3 replies, in forum: Early CJ5 and CJ6 Tech
  11. tjg358
    Post

    Newbie here

    Welcome from Loveland, Colorado
    Post by: tjg358, Apr 23, 2007 in forum: Intermediate CJ-5/6/7/8
  12. tjg358
    Post

    dual gas tank idea/question

    I used a 3 position switch and early bronco switch plate to show Aux. or Main tank.
    Post by: tjg358, Apr 20, 2007 in forum: Early CJ5 and CJ6 Tech
  13. tjg358
    Post

    dual gas tank idea/question

    I have a 70 with the tank in the rear. I put a tank under driver's seat, then instaled and electric valve. That way when I switch tanks my fuel...
    Post by: tjg358, Apr 20, 2007 in forum: Early CJ5 and CJ6 Tech
  14. tjg358
    Post

    Holley 470 carb

    You didnt re-jet or anything but adjust? I have one on order that is due to arrive tomorrow. Q-Jet is just too much.:v6:
    Post by: tjg358, Apr 5, 2007 in forum: Intermediate CJ-5/6/7/8
  15. tjg358
    Post

    Disc Brake Conversion

    Is everyone that is doing the GM conversion drilling out the brackets. Couldn't you clock the bracket up a bit more? Does anyone have a photo of...
    Post by: tjg358, Apr 4, 2007 in forum: Early CJ5 and CJ6 Tech
  16. tjg358
    Thread

    Shifter Knobs

    I have a T18 with reverse up at 3rd gear. Where can I find a new knob for it? I wouldn't mind one that was without pattern even. I could always...
    Thread by: tjg358, Mar 19, 2007, 8 replies, in forum: Early CJ5 and CJ6 Tech
  17. tjg358
    Post

    Front end swings when I crank the wheel.

    Mine did that too. I had to replace the Ubolts, they had worked loose.
    Post by: tjg358, Mar 19, 2007 in forum: Early CJ5 and CJ6 Tech
  18. tjg358
    Post

    FreeLock hubs

    They were made by Wienand/Bestop up until late 80's. I have a set for Toyota. Some of the internal parts are interchangeable. If you are...
    Post by: tjg358, Mar 13, 2007 in forum: Early CJ5 and CJ6 Tech
  19. tjg358
    Thread

    225 Motor Mounts

    Where can I find a set of motor mounts for my 70 CJ with 225?:v6:
    Thread by: tjg358, Feb 21, 2007, 2 replies, in forum: Early CJ5 and CJ6 Tech
  20. tjg358
    Post

    Will a Kay line top fit on Bestop hardware?

    Kayline 200 E. 64th Ave Denver, CO 80221 1-800-525-8118 Local:(303) 427-4242 Fax:(303) 430-7241
    Post by: tjg358, Feb 13, 2007 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2
New Posts