1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Starting the motor up... questions

Discussion in 'Early CJ5 and CJ6 Tech' started by DanStew, Sep 10, 2005.

  1. Sep 10, 2005
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    well i cranked it over again and got the timing set down and the idle running good. it still seems to have a miss, but i think it might be rough by design. But i have a few questions

    1. Will the lifter noise go away when they get enoguh oil. I did dd oil to the lifters when i installed them (new) but i can hear them or something clacking away. It seems to have gotten a bit better.

    2. i have what seems to be a vaccum leak, but cant find it, no oil leaks and the carb cleaner doesnt make it idle better. given it may be that my ear is right next to the air cleaner opening so i think it may be me over thinking stuff. Just trying to get used to the motor again.
     
    DanStew, Sep 10, 2005
    #1
  2. Sep 10, 2005
    Mcruff

    Mcruff Earlycj5 Machinist

    Albertville, AL
    Joined:
    Sep 22, 2002
    Messages:
    5,349
    Are you saying that you did bleed the lifters with fresh engine oil before installing them, if you did not that will make the lifters clatter and can sound bad.
     
    Mcruff, Sep 10, 2005
    #2
  3. Sep 10, 2005
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    i did add oil and used the pushrod to bleed them, not sure if i did it correctly.

    What i did was
    place the new lifter upright
    add oil to the top
    take a pushrod and cycle it through

    Thats about it. Billy said to add oil to it, but i didnt know bout anything else. none of the books i had made any reference to bleeding the lifters
     
    DanStew, Sep 10, 2005
    #3
  4. Sep 10, 2005
    1stSgt

    1stSgt Sponsor

    Stokesdale, N.C.
    Joined:
    Jul 20, 2003
    Messages:
    29
    You should put the lifters in a shallow pan or can. Add oil just over the tops of the lifters. Then use a push rod to bleed off the air. Oil enters the lifters from the side and exits thru the top. The noise should go away after a while. Hows the oil pressure?
     
    1stSgt, Sep 10, 2005
    #4
  5. Sep 10, 2005
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    oil pressure is just fine. about 60-80 at startup.
     
    DanStew, Sep 10, 2005
    #5
  6. Sep 10, 2005
    jd7

    jd7 Sponsor

    Nacogdoches,Texas
    Joined:
    Mar 30, 2004
    Messages:
    1,745
    Used to run a little ATF upon startup seems to quiet them down quickly. I was changing oil at 500 miles anyway.
     
    jd7, Sep 10, 2005
    #6
  7. Sep 10, 2005
    Patrick

    Patrick Super Moderator Staff Member

    Los Alamos, NM
    Joined:
    Sep 22, 2002
    Messages:
    8,360
    Those lifters will pump up Dan..... Just don't let the motor turn too fast until they do....
     
    Patrick, Sep 10, 2005
    #7
  8. Sep 10, 2005
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    thanks guys!! I will stop worrying. I am just running the motor at idle now. Tomorrow i will drive around the block, probably not get any real speed, jsut cruise around :)
     
    DanStew, Sep 10, 2005
    #8
  9. Sep 10, 2005
    Patrick

    Patrick Super Moderator Staff Member

    Los Alamos, NM
    Joined:
    Sep 22, 2002
    Messages:
    8,360
    Carefull Danny, keep the tires on the ground.........:D
     
    Patrick, Sep 10, 2005
    #9
  10. Sep 10, 2005
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    i might try to flex on a parking block or 2
     
    DanStew, Sep 10, 2005
    #10
New Posts