1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Ubolts And Plates Urgent Help!

Discussion in 'Intermediate CJ-5/6/7/8' started by ShnitzlHaus, May 22, 2016.

  1. May 22, 2016
    ShnitzlHaus

    ShnitzlHaus Member

    Toronto, Canada
    Joined:
    May 1, 2010
    Messages:
    61
    hoping I can be schooled on ubolts and ubolt plates.
    I need to put an order in tomorrow to get a discount!

    I am running a dana 30 front, and a dana 44 rear.

    I measured the tubes and they both are at 2.5'' (dana 30 - 2.5105'' dana 44 - 2.5400'')
    The dana 30 on the passenger side casting that would take a larger ubolt measures 3.125''

    what u bolts should I order? I currently have 8 new u bolts that measure 2.8150 inside to inside I am unsure if this is okay to use? I hate to spend more money to get the same ubolts. (they flop around the tubes, I figured they should be very tight)


    lastly!
    spring plates, what do I need to order? plates off a M38 for the rear dana 44 and maybe plates off a 79 cj7 for the front? (side note, what should the measurements on the spring plates be, I have some for the rear but both ubolt holes differ on each, they came off a m38!)


    I would greatly appreciate any help.
     
  2. May 22, 2016
    zila

    zila I throw poop

    Rock Springs,...
    Joined:
    Oct 6, 2003
    Messages:
    1,201
    One of the U-bolts on the 30 is larger as it fits over the punkin next to the axle tube.. I have a set of front D30 plates from my heap. I swapped in a D44. Or you could look at R&P as they probly have the plates and bolts you need.
     
  3. May 22, 2016
    Danefraz

    Danefraz Well-Known Member 2023 Sponsor 2022 Sponsor

    Chico CA
    Joined:
    Aug 11, 2012
    Messages:
    2,275
    I just bought warrior products ubolt plates withskids. I like. Morris 4x4 had a good price.

    I bought 7 or 8 inch length bolts, half inch in diameter. I will have to trim them.

    My flanged 44 is 2.75"... The d27 used 2.5" except where it rode the pumkin, used a 2.75" one there. Sounds like they are similar, the d30 just a little thicker.

    D
     
  4. May 23, 2016
    Dphillip

    Dphillip Member

    Omaha NE
    Joined:
    Nov 25, 2008
    Messages:
    322
    Most suspensions shops can make U-bolts in minutes. If your old ones were the correct size just take them to a shop and have new ones made to the same size. I just had a couple of new ones made for a recent repair and they were only 6 bucks per U-bolt.
     
  5. May 25, 2016
    zila

    zila I throw poop

    Rock Springs,...
    Joined:
    Oct 6, 2003
    Messages:
    1,201
    Yes, I use Six States, but I have seen em on the shelf at Auto Zone and O'Reilly. NAPA probly has em too
     
  6. May 25, 2016
    Danefraz

    Danefraz Well-Known Member 2023 Sponsor 2022 Sponsor

    Chico CA
    Joined:
    Aug 11, 2012
    Messages:
    2,275
    I swung into a local 4wd bling shop the other day, they had all kinds, at a 100% premium of $20/ea but they had them...
     
  7. May 25, 2016
    ShnitzlHaus

    ShnitzlHaus Member

    Toronto, Canada
    Joined:
    May 1, 2010
    Messages:
    61
    thanks for the heads up! will track em down!
     
New Posts