1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Photo Request- Ramsy PTO Winch Mount

Discussion in 'Early CJ5 and CJ6 Tech' started by Howard Eisenhauer, Dec 14, 2008.

  1. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Photo Request- Ramsey PTO Winch Mount

    O.K folks, I need some "stock" pics of a Ramsey winch on the front of a '5 detailing the placement of the mounts, a photo from ground level in front showing where the winch drive shaft passes under the x-member, a photo looking down at the drive shaft in the engine compartment and one showing the detail of how/where the mounts are attached to the frame rails. I'd also appreciate some measurements of where the mounts are bolted to the rails.

    Thanks,

    H.
     
    Howard Eisenhauer, Dec 14, 2008
    #1
  2. windyhill

    windyhill Sponsor

    Going to be out of town for a few days but can grab you aby shot you need when I'm back, shoot me a PM so I remember.
     
    windyhill, Dec 15, 2008
    #2
  3. Tom in RI

    Tom in RI Member

    Tom in RI, Dec 15, 2008
    #3
  4. windyhill

    windyhill Sponsor

    Hey Howard finally got home, here's a few pics, of the ramsey winch and also the original angle bracket that fits in the frame bolts threw the factory holes in the frame and the winch brackets rest on it. I had new ones made up there hard to see in the pics. Hope this helps.
     
    windyhill, Dec 18, 2008
    #4
  5. windyhill

    windyhill Sponsor

    one more from the front top, (rebuilding my rollers at the moment.)
     
    windyhill, Dec 18, 2008
    #5
  6. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    That's Great! :)

    I had a whole different (i.e.- Wrong :rofl:) idea on what it was supposed to look like.

    Of course, you didn't think I was going to let you off that easy, Did You? :twisted:


    Q1- How thick is the angle iron?

    Q2- The rear longitudenal looks like angle that has one side trimmed off, is that right? If so how much of the trimmed side is left?

    Q3- it looks like the front mount ties to the bumper, or maybe I'm seeing the fairlead mount, can you take a bit more detailed pic of what's happening here?


    Thanks Soooooo Much,

    H.
     
    Howard Eisenhauer, Dec 18, 2008
    #6
  7. windyhill

    windyhill Sponsor

    I tried to sketch some drawings and scan them but had trouble posting them PM me your email I'll try to send them to you.
     
    Last edited: Dec 19, 2008
    windyhill, Dec 19, 2008
    #7
  8. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    PM'd you,

    Thanks,

    H.
     
    Howard Eisenhauer, Dec 19, 2008
    #8
  9. Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    On my continuing quest to bring old posts kicking & screaming back from the grave having corresponded with windyhill I've now got what should be an accurate drawing of one style of mount-

    [​IMG]

    Ta Da!-

    [​IMG]

    A larger and somewhat less fuzzy version of this drawing dimensioned to print out on an 8.5" x 11" sheet is available here-

    http://tantel.ca/Images/The Sludge Pile/Winches/Ramsey Winch/Ramsey CJ5 High mount design.GIF


    Now, it seems there was a slightly different version as well, one that raises the winch up an inch or two from WH's version-

    [​IMG]

    If any of you out there have one of these I'd appreciate it if you could send me some measurements, I'd like to do up a drawing for that style as well.

    Thanks again to windyhill :)

    H.

    p.s.- for the recidivists who've snuck in amongst us here's a drawing for a truck/waggie mount supplied to me a while back by Tom Jacoby from the Willys Tech mail list-

    http://tantel.ca/Images/The Sludge Pile/Ramsey Winch Manual/Ramsey Winch Mount.gif
     
    Last edited: Sep 25, 2009
    Howard Eisenhauer, Feb 7, 2009
    #9
  10. windyhill

    windyhill Sponsor

    No problem Howard and thanks for all the work putting it into a readable format.:) Looks Great!

    Is it possable to start a PTO / accessories section in the tech library? I was thinking a section with part#'s for bearings etc. and drawings etc. for winches, gearboxes, PTO's etc. I have most of the part #'s now for rebuilding ramsey pto's as well as a rear gearbox.
     
    Last edited: Feb 7, 2009
    windyhill, Feb 7, 2009
    #10
  11. jglad

    jglad Village Idiot

    What is the size of the 4 bolts that hold the front and rear mounts to the side mounts? Also, what size are the bolts holding the side brackets to the frame rails?
     
    jglad, Sep 25, 2009
    #11
  12. gotime

    gotime Sick with the car bug

    I'm interested in what jglad asked as well. I'd also noticed the measurments for where the holes are on the front and rear bracket where they mount to the side brackets are missing. Can someone confirm the proper measurements?
     
    gotime, Feb 24, 2010
    #12
  13. mdmeltdown

    mdmeltdown Member

    If you guys are interested I just rebuilt my 200r and my stock plate looks different than that one. Also, I had a machine shop build a mounting plate to hold the carrier bearing on the drive line that goes on a v6. It bolts on the front of the bell housing. I kept all the boxes of seals that went into the winch. I've also got the empty seal boxes for a single stick PTO.

    Here's some pics of the winch and that carrier bearing plate

    http://www.flickr.com/photos/mdmeltdown/4035964814/
     
    mdmeltdown, Feb 26, 2010
    #13