1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Shake And Break Impact Driver

Discussion in 'The Tool Shed' started by jeep2003, Mar 4, 2019.

  1. Mar 4, 2019
    jeep2003

    jeep2003 Active Member

    Vestal NY
    Joined:
    May 30, 2006
    Messages:
    1,444
    I thought this tool looked pretty interesting. It wouldnt get used very much for 50 bucks but would be nice to have around
     

    Attached Files:

    jeeper50 and ITLKSEZ like this.
  2. Mar 4, 2019
    PeteL

    PeteL Member Sponsor 2019 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    6,306
    Often thought I could make one easy enough from the parts I have around. Put a half inch socket drive on it...
     
  3. Mar 4, 2019
    Howard Eisenhauer

    Howard Eisenhauer Super Moderator Staff Member Sponsor

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    5,663
    That's what I was wondering- how well it would work on nuts/bolts but I think you'd need shallow sockets so that the impacts would be allied to the fastener instead of whatever the fastener is fastening.
     
    jeep2003 likes this.
  4. Mar 4, 2019
    Focker

    Focker I Hate Being Bi-Polar, It's Awesome. Staff Member Sponsor 2019 Sponsor

    Tri-Cities WA
    Joined:
    Aug 18, 2014
    Messages:
    5,986
  5. Mar 4, 2019
    PeteL

    PeteL Member Sponsor 2019 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    6,306
    I would tend to agree. But impacting/vibrating the general assembly while applying torque might still have effect.

    These tools are available with socket drive, but very expensive, IMHO.
     
  6. Mar 4, 2019
    Warloch

    Warloch Did you say Flattie??? Staff Member Sponsor

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    4,444
  7. Mar 4, 2019
    Howard Eisenhauer

    Howard Eisenhauer Super Moderator Staff Member Sponsor

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    5,663
    Maybe this thing and a wrench-

    [​IMG]
     
  8. Mar 4, 2019
    PeteL

    PeteL Member Sponsor 2019 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    6,306

    Many is the time...

    And here is my "extra spicy" version. Replacing rusted 120 year old 2-1/2" diameter fasteners, with rock hammer vibration.

    upload_2019-3-4_11-38-59.jpeg
     
  9. Mar 4, 2019
    Dave Deyton

    Dave Deyton Member

    Fuquay-Varina, NC
    Joined:
    Oct 12, 2003
    Messages:
    229
    Got one of those from the Snap On man on sale one time.

    Worked well on the Phillips Screws on the windshield hinges on body. Only time I have used it.

    Seemed to work well with the air hammer taking off those screws.

    Dave
     
  10. Mar 4, 2019
    jeep2003

    jeep2003 Active Member

    Vestal NY
    Joined:
    May 30, 2006
    Messages:
    1,444
    yes that is a nice tool I use the bench grinder quite often to do that. Still it would be usefull on studs and such that cant be taken to the bench
     
  11. Mar 4, 2019
    jeep2003

    jeep2003 Active Member

    Vestal NY
    Joined:
    May 30, 2006
    Messages:
    1,444
    Exactly what i was thinking. It would be good for small bolts that often just snap off.
     
  12. May 4, 2019
    jeeper50

    jeeper50 jeeps 'till I die

    Gawja
    Joined:
    Dec 20, 2007
    Messages:
    455
    That is what we in the aviation maintenance profession call a "screw knocker". With a 3/8 drive to apex bit holder, they would break loose the hundreds of screws holding the lower leading edge panels on commercial aircraft wings for access for maintenance. and when you fracture the bit and it's stuck in the screw use the empty bit holder to hammer the screw a couple of times to knock the broken piece out.
    We used a 4X rivet gun to hammer the screws loose and then an 3/8 drive impact to spin the screws out. Rivet guns have a softer "hammer action" than a air chisel.
     

Share This Page

New Posts