1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Replacing my clutch what parts do I need?

Discussion in 'Early CJ5 and CJ6 Tech' started by manden68, Jul 13, 2005.

  1. Jul 13, 2005
    manden68

    manden68 Member

    O Fries Country
    Joined:
    Jul 16, 2003
    Messages:
    214
    Replacing my clutch what parts do I need? YES I AM TOO LAZY TO DO A SEARCH. Ha.
    Pressure plate, clutch disc, throwout bearing, pilot bearing

    Is this a good deal? Does anybody have anything cheaper?

    http://www.jeepdoc.com/catalog/zproducts.asp?id=34

    Clutch Kit w/Diaphragm Clutch
    Part#: 948692K
    Model: All V6-225
    Year: 67-71 $146.95
     
  2. Jul 13, 2005
    Mcruff

    Mcruff Earlycj5 Machinist

    Albertville, AL
    Joined:
    Sep 22, 2002
    Messages:
    5,349
    Alignment tool.
     
  3. Jul 13, 2005
    tgregg

    tgregg Member

    Oak Hills, CA...
    Joined:
    Apr 14, 2005
    Messages:
    529
    The kit I got from NAPA came with an alignment tool
     
  4. Jul 13, 2005
    Project71-5

    Project71-5 BACON

    Gypsum, CO
    Joined:
    Sep 24, 2002
    Messages:
    897
    Got my kit from NAPA as well and it contained everything needed.
     
  5. Jul 13, 2005
    manden68

    manden68 Member

    O Fries Country
    Joined:
    Jul 16, 2003
    Messages:
    214
    How much ladies how much?
     
  6. Jul 13, 2005
    Project71-5

    Project71-5 BACON

    Gypsum, CO
    Joined:
    Sep 24, 2002
    Messages:
    897
    Mine was right around $200. Check out Napaonline.com
     
  7. Jul 13, 2005
    MOP

    MOP Active Member

    Pullman, WA
    Joined:
    Sep 25, 2003
    Messages:
    1,131
    Here is some info I posted a few months back

     
  8. Jul 13, 2005
    barry

    barry Inquisitive Member

    Earp, CA
    Joined:
    Sep 23, 2002
    Messages:
    195
    Got mine from Krage. Very happy.
     
  9. Jul 13, 2005
    gte636p

    gte636p Member

    smyrna, Ga
    Joined:
    Sep 23, 2002
    Messages:
    492
    personally, i've seen both and i'd go with the luk kit. the one i got from krage ha some chatter in it afte a year or so of use. i'm not going to say it was the clutches faut (i had a bt of an oil leak headed towads the disk) but the luk one looked to be a bit better built. i kind of view it as a part a little bit too important to get through omix-ada, or an equivalent supplier.
     
  10. Jul 14, 2005
    TIMBERWOLF427

    TIMBERWOLF427 Member

    Joined:
    Mar 6, 2005
    Messages:
    64
    We just put a LUK kit in our 70 CJ5 V6 and it works great. We found ours at www.dialaclutch.com for $144. There even located in Florida so that should save you on the shipping. ;)
     
  11. Jul 14, 2005
    Chris Insull

    Chris Insull All roads lead me back to the beach... 2023 Sponsor 2022 Sponsor

    Chesapeake, VA.
    Joined:
    Sep 22, 2002
    Messages:
    805
    I used a kit from Krage two years ago. For less than $200 I got the pressure plate, disk, throw out bearing, clutch fork, pilot bearing and clutch fork rubber dust boot. I also went ahead and had my flywheel resurface for about $25. No problems since.
     
  12. Jul 14, 2005
    barry

    barry Inquisitive Member

    Earp, CA
    Joined:
    Sep 23, 2002
    Messages:
    195
  13. Jul 14, 2005
    sparky

    sparky Sandgroper Staff Member Founder

    Perth, WA
    Joined:
    Sep 20, 2002
    Messages:
    9,221
    Too lazy to answer.

    Hah. :rofl:
     
  14. Jul 14, 2005
    John A. Shows

    John A. Shows Comic Relief

    Mendenhall...
    Joined:
    Sep 24, 2002
    Messages:
    938
    I'd have the flywheel resurfaced and also get a new clutch fork and maybe a pivot ball while I was at it...and unless I'm mistaken, wouldn't, couldn't you want to replace the rear main seal in the engine while you were in there?
     
New Posts