1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

How Much Rust Pitting Is Too Much?

Discussion in 'Early CJ5 and CJ6 Tech' started by 1967 CJ5A, May 23, 2019.

  1. May 23, 2019
    1967 CJ5A

    1967 CJ5A Mike 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Raleigh, NC
    Joined:
    May 12, 2012
    Messages:
    726
    After searching for quite a while, I finally sourced a two hole knuckle from a junk yard. It is not in the best condition though. What do you guys think? Is it still usable?
    (I know I could buy new, but its not really in the budget right now)
    [​IMG]
    [​IMG]
    [​IMG]

    [​IMG]
     
    1967 CJ5A, May 23, 2019
    #1
  2. May 23, 2019
    jeepstar

    jeepstar Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sheboygan
    Joined:
    Jun 28, 2006
    Messages:
    2,770
    id use that all day long. i see no reason why not. small surface rust it perfectly fine. the mating surfaces all look pretty nice.
     
    jeepstar, May 23, 2019
    #2
    Twin2, jpflat2a and Jrobz23 like this.
  3. May 23, 2019
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    942
    This
     
    Jrobz23, May 23, 2019
    #3
    mickeykelley likes this.
  4. May 23, 2019
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    Only concern I'd have is whether it will seal.
     
    timgr, May 23, 2019
    #4
    ojgrsoi likes this.
  5. May 23, 2019
    Norcal69

    Norcal69 Out of the box thinker 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Northern California
    Joined:
    Sep 6, 2014
    Messages:
    3,562
    If your concerned, fill the pitting with jb weld and sand smooth.....
     
    Norcal69, May 23, 2019
    #5
    Thean and ojgrsoi like this.
  6. May 23, 2019
    Chilly

    Chilly Active Member

    Joined:
    Mar 12, 2007
    Messages:
    1,486
    For the seal flange I'd JB Weld, then lap it on something reasonably flat. Or just flat file with a nice broad file.
     
    Chilly, May 23, 2019
    #6
  7. May 23, 2019
    windyhill

    windyhill Sponsor

    PA
    Joined:
    Nov 4, 2006
    Messages:
    1,502
    looks good to me.
     
    windyhill, May 23, 2019
    #7
  8. May 23, 2019
    Twin2

    Twin2 not him 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Virginia Beach, VA
    Joined:
    Apr 28, 2011
    Messages:
    5,420

    x2
     
    Twin2, May 23, 2019
    #8
  9. May 23, 2019
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    Sealing?.........use the std gasket and Silicon..........that's what it's for!
     
    tarry99, May 23, 2019
    #9
    jeepstar likes this.
  10. May 24, 2019
    Magiccoolbus

    Magiccoolbus New Member

    Joined:
    Apr 25, 2016
    Messages:
    16
    Magiccoolbus, May 24, 2019
    #10
    Jrobz23 likes this.
New Posts