1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Harbor Freight Chain Hoist.

Discussion in 'The Tool Shed' started by mickeykelley, Dec 13, 2017.

  1. Dec 13, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    Bought this 2 ton chain hoist from Harbor Freight (2 ton Manual Chain Hoist) to pull the engine. It actually worked out well. The only bad part was the chains were coated in oil, presumably to avoid rust in the salt water atmosphere trip from China. So first step, was to get a gas soaked rag and clean the chains. It was really messy but got most of it off. At least to get the engine out. However, I can see I need to put the chains in a bucket of kerosene and give them a good cleaning.
     
  2. Dec 13, 2017
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    What did you hang it from?
     
  3. Dec 13, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    In my hurry to get the engine over to the rebuilder, I forgot to take a pic of it hanging. I have a bobcat so I put the forks on and put a very heavy 1950's era railroad pry bar between them and hung it from that with the boom raised to its highest position and the service safety brace in place just in case. Over kill picking the 2 ton unit, pry bar and service brace but was doing it all by myself so I wanted to take extra precautions.
     
    Focker likes this.
  4. Dec 14, 2017
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    I have one of the Chinese chain hoist hanging from a truss I built in my garage. I use gloves to handle the chain - it's still covered with an oil coating.
     
    47v6 likes this.
  5. Dec 14, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    I still got some grease on my gloves even after wiping over and over with the gas soaked rag. So I've pretty much decided to put the chains in a bucket of gas and let them soak for a day. Hopefully it will get it all off. I just hate having to use tools full of grease. So before I put the engine back in Willie and before I pull the engine out of Wilbur (the 55 wagon) it's gotta get done.
     
  6. Dec 15, 2017
    47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    USA
    Joined:
    Oct 25, 2006
    Messages:
    5,798
    I have one too. I use gloves to run the chain as well. The thing works well for engines, but I would make sure to leave a good margin between the rated weight and the actual weight you are lifting. Chinese cheap products do not equal safety.
     
  7. Dec 15, 2017
    mickeykelley

    mickeykelley Well-Known Member

    Republic of Texas
    Joined:
    Oct 10, 2015
    Messages:
    1,900
    That was part of my decision to get a 2 ton to handle a 500 pound engine. In fact there were comments to that effect in the reviews.
     
  8. Dec 15, 2017
    rejeep

    rejeep Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Rochester, NY
    Joined:
    Nov 5, 2009
    Messages:
    1,691
    I have a performance tool one.. (90 percent likelihood same manufacture)

    same as Tim.. I use gloves

    its been wonky lately and the auto hold from time to time wont 'catch' well..
    I only use it for up and down now.. no mid air acrobatics..
     
  9. Dec 15, 2017
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    I have like a PTSD relapse going on from reading about these chain hoists. When I was an iron worker, our "bread and butter" jobs were building and installing the fire-safe stairwells in the four corners of new hotel buildings all over New England.

    The stairwells begin life as a 3-to-5-story cement block tube with holes in the sides that our steel would stab into. We'd beg the jobsite's crane operator relentlessly until he'd drop a top truss on top to mount two of those chain hoists on, then lift every piece one at a time with the chain hoists. They were sooooo slooooow. And these old monsters had no release, so while one guy was lifting, another guy was cranking on the other one to lower it back down to rehook. Max the travel out on one, swap the load and do it again. :cry:
     
  10. Dec 15, 2017
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    I've got a 2 ton one simply because when I needed it it was on sale cheaper than the one ton. The oily chain is *really* oily but in this climate I'm leaving it that way- better oily than rusty.
     
  11. Dec 15, 2017
    jeepermc

    jeepermc Active Member

    Western WA
    Joined:
    May 25, 2011
    Messages:
    1,188
    I can't even remember where I inherited it from I got an old Yale chain hoist. Had no use for one and couldn't hardly give it away..... I prefer a standard engine hoist.
     
  12. Dec 16, 2017
    dozerjim

    dozerjim Member

    western New York
    Joined:
    Nov 22, 2010
    Messages:
    966
    I have an old American made chain hoist on my gantry,I like it much better than my hydraulic hoist,never drifts,can't move too fast(as in opening the valve too much)
     
  13. Dec 16, 2017
    Andy Salagaj

    Andy Salagaj Joshua70x7

    Colorado
    Joined:
    Aug 3, 2016
    Messages:
    33
    I have the same HF chain hoist and I have pulled a couple engines and moved some trannies around with it - no problems so far - gets the job done. If I was a pro mechanic though I'd invest in a better one. Is it just me or is HF stuff getting a bit better over the years?
     
  14. Dec 16, 2017
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    I think some of the stuff is....And some things will remain junk.
     
  15. Dec 16, 2017
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    On Garage Journal, it was suggested that HF is actively moving into the space left by Sears when they sold the Craftsman brand. Supposedly Stanley-B&D is moving to offer the brand under some new retail arrangement, but right now there is an opportunity for HF. They have many new brand names that may have been introduced to escape the stigma of the older names. Just speculation ...
     
  16. Feb 4, 2018
    Rick Whitson

    Rick Whitson Detroit Area 2024 Sponsor 2022 Sponsor

    I live South of...
    Joined:
    Dec 2, 2014
    Messages:
    1,725
    Being a Retired Ironworker, I have all the different safe hoisting tools I need. My Boss would give me anything I wanted, but after the job was over. I don't need a lot of big heavy duty stuff we used, just the little stuff, half ton stuff.
     
New Posts