1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Pcv Valve Connector

Discussion in 'Early CJ5 and CJ6 Tech' started by Don X, Jul 27, 2021.

  1. Jul 27, 2021
    Don X

    Don X The Prodigal Moderator Staff Member 2023 Sponsor

    San Diego,...
    Joined:
    Mar 30, 2007
    Messages:
    3,383
    What is the proper name of the connector in the pics below? Does anyone have a source or P/N? Thanks.

    [​IMG]

    [​IMG]
     
    Don X, Jul 27, 2021
    #1
  2. Jul 27, 2021
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,823
    Last edited: Jul 27, 2021
    PeteL, Jul 27, 2021
    #2
    Don X and scoutpilot like this.
  3. Jul 28, 2021
    Steve's 70-5

    Steve's 70-5 Active Member

    Louisville, Ky
    Joined:
    Nov 12, 2009
    Messages:
    1,383
    Reducing Bushing
     
    Steve's 70-5, Jul 28, 2021
    #3
    Don X likes this.
  4. Jul 28, 2021
    Don X

    Don X The Prodigal Moderator Staff Member 2023 Sponsor

    San Diego,...
    Joined:
    Mar 30, 2007
    Messages:
    3,383
    I checked with Mike at Kaiser Willys. He said he doesn't carry it but that NAPA will have it. Just tell them to look in their Weatherhead book. My PCV is 75 miles away and I don't know what size the fitting needs to be. Does anyone here have one on which they can check the thread sizes?
     
    Don X, Jul 28, 2021
    #4
  5. Jul 28, 2021
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,376
    Is your's setup the same? I originally was thinking 2 different thread sizes but maybe not....maybe 1/8" pipe, maybe a 1/4"? Pipe shows up easily enough, but the PCV side is dark so it's hard to guess.
     
    Last edited: Jul 28, 2021
    Glenn, Jul 28, 2021
    #5
  6. Jul 28, 2021
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,823
    Technically a bushing has external (male) threads. This is female at both ends.
     
    PeteL, Jul 28, 2021
    #6
  7. Jul 29, 2021
    Don X

    Don X The Prodigal Moderator Staff Member 2023 Sponsor

    San Diego,...
    Joined:
    Mar 30, 2007
    Messages:
    3,383
    Here's my PCV. I'm trying to figure out what size reducing coupling is needed or the left end of the valve.

    [​IMG]
     
    Don X, Jul 29, 2021
    #7
  8. Jul 29, 2021
    Rick Whitson

    Rick Whitson Detroit Area 2024 Sponsor 2022 Sponsor

    I live South of...
    Joined:
    Dec 2, 2014
    Messages:
    1,730
    Don, couldn't you put a 1/8th nipple and a 1/8th to 1/4 coupling then the PCV on it instead of two elbows? Do you have Vacuum wipers?, Just a thought.
     
    Rick Whitson, Jul 29, 2021
    #8
  9. Jul 29, 2021
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,376
    I know, me too. Looking at this picture again I'd say 1/4". I agree with Rick's idea too.
     
    Glenn, Jul 29, 2021
    #9
New Posts