1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Roxor Dana 44 Full Floater Kit

Discussion in 'Roxor Tech' started by Bigdaddy13, Jan 4, 2021.

  1. Jan 4, 2021
    Bigdaddy13

    Bigdaddy13 Member 2021 Sponsor 2020 Sponsor

    So.Cal
    Joined:
    Nov 19, 2019
    Messages:
    558
  2. Jan 4, 2021
    wheelie

    wheelie beeg dummy 2021 Sponsor

    York, PA
    Joined:
    Mar 6, 2004
    Messages:
    4,246
    Give them a call. Looks like a nice kit.
     
  3. Jan 4, 2021
    Jay's WWII Jeeps

    Jay's WWII Jeeps Member 2021 Sponsor 2020 Sponsor

    Napa CA
    Joined:
    Mar 14, 2018
    Messages:
    156
    From the research that I have done, the rear axle is wider than a CJ. I would look a Herms kit or build your own. Here is a great post about building a full floater 44 with one piece flanged shafts. This is what I did. and made it match my Rotor 44 front for width.
    Jay
    Sanity Check, D44 Full Floater
     
  4. Aug 15, 2021
    my 66

    my 66 Member

    carson city, nevada
    Joined:
    Dec 1, 2008
    Messages:
    60
    So what is the WMS to WMS distance for a Roxor Dana 44 front end?
    Because I've already have a front end that is 60" WMS to WMS and I can modify the spare rear 44 that I have to use there full floater kit.
     
  5. Aug 15, 2021
    Jrobz23

    Jrobz23 Member

    Northern, WI
    Joined:
    Oct 3, 2016
    Messages:
    941
    It’s gotta be hella close to the NT D30. Within an inch or so I’d guess.

    I always figured that front would make for a hot swap candidate.
     
    Downs likes this.
  6. Mar 3, 2022
    jpflat2a

    jpflat2a what's that noise?

    Riverside CA
    Joined:
    Jul 30, 2003
    Messages:
    8,413
    So has anyone done this Roxor FF kit ?
     
  7. Mar 19, 2022
    duffer

    duffer Rodent Power

    Bozeman, MT
    Joined:
    Sep 17, 2009
    Messages:
    3,817
    Looking at the photos, that kit will require removing the spindles for the axle install and looks to use the Set 47/Set 45 bearings-or perhaps some metric equivalent. The reduction in shaft diameter for the 27 spline drive flanges is what sanity check was really all about That and the price isn't any cheaper than what one can put together themselves. I found an original pair of Dana D30 disc brake hubs on flebay for $45, the one piece Dutchman moly shafts were about $400 for the pair, the custom 4340 jpet spindles $300 and I'm certain the bearings, fasteners (all ARP 8740) and seals didn't come anywhere close to the $400 difference. Another case of no free lunch.
    [​IMG]
     
    Fireball likes this.
  8. Mar 19, 2022
    Jay's WWII Jeeps

    Jay's WWII Jeeps Member 2021 Sponsor 2020 Sponsor

    Napa CA
    Joined:
    Mar 14, 2018
    Messages:
    156
    This is what I'm doing. Except I'm using a set of brakes from Sam at Partsdude, I also had Jeff to make a spacer to bring the axel to the same width as a Roxor front 44.
    Jay
     
New Posts