1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

My 67 CJ5 build

Discussion in 'Builds and Fabricators Forum' started by Johns1967CJ5, Dec 11, 2013.

  1. Dec 11, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    So here we go. I posted some of these photos on the resto forum when asking some questions so I decided to start a thread of my project. This is a 1967 CJ5 V6 225 engine, t-86 transmission, pto winch. The Jeep was my fathers and he used it for hunting in NY. I've been working on this on and off for a couple of years, taking a lot of " financial " breaks lol. I will post what I've done a little at a time to get you caught up to where I am today.

    [​IMG]

    [​IMG]

    How the Jeep looked when I got it from my father. It has a different body on it we put on from a junk yard. That was shot too.

    [​IMG]

    [​IMG]


    So I won't bore you with the disassembly photos but when the body was taken off here is the damage I found to the frame

    [​IMG]

    [​IMG]

    [​IMG]

    Old repair

    [​IMG]
     
    Last edited: Aug 4, 2017
  2. Dec 11, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    Repairs made

    Going to my friends who has torches to cut bumpers off
    [​IMG]


    [​IMG]

    [​IMG]

    [​IMG]






    Sandblasting

    [​IMG]
    [​IMG]
    [​IMG]
     
    Last edited: Aug 5, 2017
  3. Dec 11, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    I made a redneck rotisserie to paint the frame. I used Por-15. Sprayed it with metal ready and allowed it to flash rust which is recommended. then 2 coats of Por-15 and 2 coats of Por-15 chassis coat satin black.

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
     
    Last edited: Aug 5, 2017
    Stano316, BJHitson60 and Danefraz like this.
  4. Dec 11, 2013
    tomatolane

    tomatolane Lane

    Chattanooga...
    Joined:
    Sep 3, 2012
    Messages:
    465
    Hell yeah looking good.

    Are you going to restore the top also?

    That style of hard top is my fav.
     
  5. Dec 11, 2013
    givemethewillys

    givemethewillys Been here since sparky ran it. 2022 Sponsor

    New Kent, VA
    Joined:
    Jun 21, 2005
    Messages:
    2,113
    Looking good! I had that same top before falling icicles crushed it :( that frame looks mighty good too, keep up the good work!
     
  6. Dec 11, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    A falling tree made that decision for me :-(
     
  7. Dec 11, 2013
    tomatolane

    tomatolane Lane

    Chattanooga...
    Joined:
    Sep 3, 2012
    Messages:
    465
    ACK!! :(

    That sux
     
  8. Dec 12, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    After the frame was complete I started on the axles. There was no major issues with them when on the road so I just checked the bearings and replaced the oils seals. Sandblasted and painted with Por-15

    [​IMG]

    I had to cut one of the brake drums off with a skill saw

    [​IMG]

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]


    New oil seal

    [​IMG]
    [​IMG]
    [​IMG]

    Paints still wet, thats why so shiny

    [​IMG]
    [​IMG]
    [​IMG]
     
    Last edited: Aug 5, 2017
    melvinm and Mark T. like this.
  9. Dec 12, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    Backing plates sandblasted and painted

    [​IMG]

    [​IMG]



    [​IMG]

    [​IMG]
     
    Last edited: Aug 6, 2017
    melvinm likes this.
  10. Dec 12, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    Front axle went pretty much the same way. I purchased new felt seal kits for the knuckles, and new king pins and king pin bearings. Will put those in after axles gets mounted to the frame.

    [​IMG]

    [​IMG]

    [​IMG]
     
    Last edited: Aug 5, 2017
    melvinm likes this.
  11. Dec 15, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    The Ross steering gear was next

    [​IMG]

    [​IMG]

    Worm gear in great condition so I reused it

    [​IMG]
    [​IMG]

    Sandblasted all the parts, new bearings and race's

    [​IMG]

    The original sector shaft was worn so after a long search finally found a NOS shaft and new brass bushing

    [​IMG]
    [​IMG]
    [​IMG]
    [​IMG]

    [​IMG]

    [​IMG]

    Pressing in the new bushing

    [​IMG]

    Used a brake cylinder hone to get the right oil clearance

    [​IMG]
    [​IMG]
    [​IMG]

    All done and primed

    [​IMG]
    [​IMG]
     
    Last edited: Aug 6, 2017
    melvinm likes this.
  12. Dec 15, 2013
    rusty

    rusty Well-Known Member

    norfolk,va
    Joined:
    Dec 16, 2006
    Messages:
    1,663
    Nice work. Looking forward to seeing this go together .
     
  13. Dec 16, 2013
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,509
    Got to ask - how much weight did you have in the bottom of that can to support the axle so it wouldn't fall over :D

    And yes - looks real nice. I hope to give that much detail to one again in the near future.
     
  14. Dec 16, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697

    You don't like my work bench ? lol It was properly balanced, no issue jeep toss
     
  15. Dec 16, 2013
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,509
    I love it - just that when we tried it I think it broke a toe on my cousin's foot when it fell over :D
     
  16. Dec 16, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    Ouch!
     
  17. Dec 16, 2013
    68BuickV6

    68BuickV6 Well-Known Member

    Hesperia, CA.
    Joined:
    Mar 12, 2012
    Messages:
    2,183
    Nice work on the Ross box, it looks good.


    I'm envying that workbench! If I had that kinda space I could actually get stuff done!
     
    Mark T. likes this.
  18. Dec 16, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    If you mean the real bench and not the garbage can :) it's laminated beams turned on there side. Put some angle iron under them to hold together. 4x4 for legs.
     
  19. Dec 29, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    where do I begin ? :)

    [​IMG]
    [​IMG]
     
    Last edited: Aug 6, 2017
  20. Dec 29, 2013
    Johns1967CJ5

    Johns1967CJ5 Sponsor

    Northern NJ
    Joined:
    Dec 5, 2013
    Messages:
    1,697
    Disassembled the T-86 today

    [​IMG]
    [​IMG]
    [​IMG]

    Thank god I'm replacing these :)

    [​IMG]
    [​IMG]

    Found some damage

    [​IMG]

    [​IMG]

    [​IMG]
     
    Last edited: Aug 27, 2017
New Posts