1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. Dave M
    Post

    Engine Rebuild Saga

    Hmmmm, interesting reply. Good day sir
    Post by: Dave M, Jul 8, 2022 in forum: Intermediate CJ-5/6/7/8
  2. Dave M
    Thread

    Engine Rebuild Saga

    Good evening folks, So I got to the engine part of the '74 cj5, it's a 258 1bbl. After the removal of the manifold(s) discovered where the exhaust...
    Thread by: Dave M, Jul 6, 2022, 3 replies, in forum: Intermediate CJ-5/6/7/8
  3. Dave M
    Post

    Heater Box Rebuild

    Yup familiar with McMaster Carr. Wouldn't you know there are different textures or stiffness that's available (what a country). It's a real treat...
    Post by: Dave M, Jun 30, 2022 in forum: Intermediate CJ-5/6/7/8
  4. Dave M
    Post

    Heater Box Rebuild

    In the process of repairing the heater in a '74 Cj5. This is the fresh air flap. To replace the gasket I'd have to split the metal part of the...
    Post by: Dave M, Jun 30, 2022 in forum: Intermediate CJ-5/6/7/8
  5. Dave M
    Post

    Spring Mount Repair

    I purchased new bushings, the bushing fits in between the mount. It seems the movement of the bolt wears against the mount itself. I agree filling...
    Post by: Dave M, May 24, 2022 in forum: Intermediate CJ-5/6/7/8
  6. Dave M
    Post

    Spring Mount Repair

    Here's a pic. I hope[ATTACH] [ATTACH]
    Post by: Dave M, May 24, 2022 in forum: Intermediate CJ-5/6/7/8
  7. Dave M
    Post

    Spring Mount Repair

    Thanks, I'll try to load a pic tomorrow. This is where the spring mounts to, so there is no sleeve.
    Post by: Dave M, May 24, 2022 in forum: Intermediate CJ-5/6/7/8
  8. Dave M
    Post

    Spring Mount Repair

    Ok sorry about that. The previous picture is a warbled out hole in the spring mount, '74 CJ5. I was thinking of filling in the hole, then welding...
    Post by: Dave M, May 21, 2022 in forum: Intermediate CJ-5/6/7/8
  9. Dave M
    Thread

    Spring Mount Repair

    [IMG]
    Thread by: Dave M, May 21, 2022, 9 replies, in forum: Intermediate CJ-5/6/7/8
  10. Dave M
    Post

    Rear Dif Vent '74 Cj5

    Got it. Thanks
    Post by: Dave M, May 12, 2022 in forum: Intermediate CJ-5/6/7/8
  11. Dave M
    Thread

    Rear Dif Vent '74 Cj5

    Is the vent for the rear end (Dana 44) that is on the tube sufficient or should I drill and tap (1/8") the pumpkin? I want to extend the vent...
    Thread by: Dave M, May 10, 2022, 4 replies, in forum: Intermediate CJ-5/6/7/8
  12. Dave M
    Post

    Dana 30 Dif And Spindle Seal Id

    Agreed, The Spicer was the cross reference to the new style , checked at the parts store yesterday. At first look, it looked like it should have...
    Post by: Dave M, Apr 12, 2022 in forum: Intermediate CJ-5/6/7/8
  13. Dave M
    Post

    Dana 30 Dif And Spindle Seal Id

    The side facing up on the new one is the sprig side. There must be different seals for the 30.
    Post by: Dave M, Apr 11, 2022 in forum: Intermediate CJ-5/6/7/8
  14. Dave M
    Post

    Dana 30 Dif And Spindle Seal Id

    Here's a picture. The left side is the one that was in there, right is new. It says it's for a Dana 30. Going to try a local parts store. I have...
    Post by: Dave M, Apr 11, 2022 in forum: Intermediate CJ-5/6/7/8
  15. Dave M
    Thread

    Dana 30 Dif And Spindle Seal Id

    Hello, I'm replacing the seals and bearings as needed on the front differential on my 74 cj5. Picked up a new pinion seal which isn't a match to...
    Thread by: Dave M, Apr 10, 2022, 12 replies, in forum: Intermediate CJ-5/6/7/8
  16. Dave M
    Post

    Front Spindle Removal

    h For those unfamiliar; here's a pic of the spindle removal tool and a slide hammer
    Post by: Dave M, Apr 6, 2022 in forum: Intermediate CJ-5/6/7/8
  17. Dave M
    Post

    Front Spindle Removal

    That'll do it. Thanks, Dave
    Post by: Dave M, Apr 1, 2022 in forum: Intermediate CJ-5/6/7/8
  18. Dave M
    Thread

    Front Spindle Removal

    Hello, Would anyone happen to know the thread size of the spindle or perhaps the part number of the adapter that connects to a slide hammer for...
    Thread by: Dave M, Apr 1, 2022, 20 replies, in forum: Intermediate CJ-5/6/7/8
  19. Dave M
    Post

    I Cannot Figure Out The Horn Setup At The Column On My 73

    Maybe this will help. There is a plastic retainer sleeve that the brass sleeve fits over. The horn button wire runs down the shaft and out the...
    Post by: Dave M, Mar 16, 2022 in forum: Intermediate CJ-5/6/7/8
  20. Dave M
    Post

    72-75 Steering Column And Shaft

    Thank you for all your help. Dave
    Post by: Dave M, Mar 15, 2022 in forum: Intermediate CJ-5/6/7/8
Showing results 1 to 20 of 33 Next >
Search Again
Page 1 of 2
New Posts