1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 9
  1. jasonjp62
    Post

    Question For The Hardtop Guys.

    If you come across them I’ll take you up on them. Thanks man!
    Post by: jasonjp62, Sep 8, 2020 in forum: Early CJ5 and CJ6 Tech
  2. jasonjp62
    Post

    Question For The Hardtop Guys.

    Thanks for the replies gentlemen! Ill work on it slowly. Hate to say it but my old Jeep lives in the garage 98% of the time anymore. I may drive...
    Post by: jasonjp62, Sep 7, 2020 in forum: Early CJ5 and CJ6 Tech
  3. jasonjp62
    Thread

    Question For The Hardtop Guys.

    I just acquired a hard top last week. It’s either a Kelly, or a Meyer. It’s missing the fill in pieces for around the windshield and missing the...
    Thread by: jasonjp62, Sep 7, 2020, 34 replies, in forum: Early CJ5 and CJ6 Tech
  4. jasonjp62
    Post

    Torque Wrench

    I have a CDI in my company truck. We use them allot but I'm not that impressed with them. Would much rather have a Williams or snap on
    Post by: jasonjp62, Sep 1, 2016 in forum: The Tool Shed
  5. jasonjp62
    Post

    Harbor Freight

    I have one too works great. For occasional use. I do feel the boom is a lil short at times but I have a pretty big bumper on my jeep.
    Post by: jasonjp62, Aug 17, 2016 in forum: The Tool Shed
  6. jasonjp62
    Post

    Runs terrible, idle is fine, no power and just breaks up. f-134 timing problem?

    Depends on what distributor you have. Autolite .020 point gap and the dwell at 42 Delco .022 point gap and the dwell at 25-34
    Post by: jasonjp62, May 4, 2014 in forum: Early CJ5 and CJ6 Tech
  7. jasonjp62
    Post

    F head miss under load

    I have been out of town, so I haven't had time to mess with it. I did pull the tank a few weeks ago and it was a mess. I will get back to ya all...
    Post by: jasonjp62, Apr 21, 2014 in forum: Early CJ5 and CJ6 Tech
  8. jasonjp62
    Post

    Smittybilt low back seats in a 1957 - report

    I have had the high back seats from Smittybilt in my 5 for 7 years now they have been thru allot and have held up really well.
    Post by: jasonjp62, Apr 8, 2014 in forum: Early CJ5 and CJ6 Tech
  9. jasonjp62
    Post

    F head miss under load

    Ok it's back, coming home this afternoon it started this back up. I was really listening to it and it is popping thru the carb. It would hardly...
    Post by: jasonjp62, Apr 8, 2014 in forum: Early CJ5 and CJ6 Tech
  10. jasonjp62
    Post

    F head miss under load

    Thank you guys for the ideas, Walt and Pete pretty much nailed what it was, I tore the distributor apart cleaned everything up adjusted the points...
    Post by: jasonjp62, Apr 7, 2014 in forum: Early CJ5 and CJ6 Tech
  11. jasonjp62
    Post

    F head miss under load

    Pete is on to it here. I haven't gotten it figured out completely yet but It is something in the timing, or mechanical advance. gonna mess with it...
    Post by: jasonjp62, Apr 5, 2014 in forum: Early CJ5 and CJ6 Tech
  12. jasonjp62
    Post

    F head miss under load

    "When you say "under load," do you mean like lugging uphill? Or do you mean speed?" Pete it does it at speed, I have a long hill just past my...
    Post by: jasonjp62, Apr 5, 2014 in forum: Early CJ5 and CJ6 Tech
  13. jasonjp62
    Thread

    F head miss under load

    Ok guys I bounce something off of you F head guys? I have a bad miss and loss of power in my F head when you are at cruising speed and engine is...
    Thread by: jasonjp62, Apr 4, 2014, 24 replies, in forum: Early CJ5 and CJ6 Tech
  14. jasonjp62
    Post

    Hand throttle to Carter YF

    [IMG] This is on a solex, but its the same principle. like Pete described. I am missing the stop on the end of the cable.
    Post by: jasonjp62, Mar 31, 2014 in forum: Early CJ5 and CJ6 Tech
  15. jasonjp62
    Post

    Hand throttle to Carter YF

    [IMG]
    Post by: jasonjp62, Mar 30, 2014 in forum: Early CJ5 and CJ6 Tech
  16. jasonjp62
    Post

    Hand throttle to Carter YF

    [IMG]
    Post by: jasonjp62, Mar 30, 2014 in forum: Early CJ5 and CJ6 Tech
  17. jasonjp62
    Post

    Hand throttle to Carter YF

    [IMG]
    Post by: jasonjp62, Mar 30, 2014 in forum: Early CJ5 and CJ6 Tech
  18. jasonjp62
    Post

    Hand throttle to Carter YF

    http://www.ebay.com/itm/Jeep-MB-GPW-M38-M38A1-CJ2A-CJ3A-CJ3B-CJ5-CJ7-GPA-Throttle-Cable-Stop-NOS-G503-/181115637324?pt=Vintage_Car_Truck_Parts_Acce...
    Post by: jasonjp62, Mar 30, 2014 in forum: Early CJ5 and CJ6 Tech
  19. jasonjp62
    Thread

    turn signal switch

    [IMG] I'm needing this turn signal switch for the 77 postal column in my 5 Would anyone know where I could get it any cheaper? a 100 bucks is a...
    Thread by: jasonjp62, Mar 24, 2014, 1 replies, in forum: Early CJ5 and CJ6 Tech
  20. jasonjp62
    Post

    Dana 27 pinion bearing

    Been there done that, Nick is correct!
    Post by: jasonjp62, Mar 14, 2014 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 172 Next >
Search Again
Page 1 of 9
New Posts