1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. torque
    Post

    T-case Shifter Boot

    I made one using the rubber seal from the master cylinder cover from a Chevy pickup. It has been on there for 10 years and shows no sign of...
    Post by: torque, Apr 1, 2024 in forum: Early CJ5 and CJ6 Tech
  2. torque
    Post

    Dana 18 Not Shifting Back Into 2h

    I looked at my dana 30 and I have a 4.88 now so only need the 5.38 r&p. Would have the 4.88 set for sale!
    Post by: torque, Sep 24, 2022 in forum: Early CJ5 and CJ6 Tech
  3. torque
    Post

    Dana 18 Not Shifting Back Into 2h

    If you want to sell the dana 30 5.38 gear set and carrier, I have need of one.
    Post by: torque, Sep 23, 2022 in forum: Early CJ5 and CJ6 Tech
  4. torque
    Post

    Monroe Three Point Lift Color?

    I always assumed they were Ford tractor red.
    Post by: torque, Sep 28, 2020 in forum: Early CJ5 and CJ6 Tech
  5. torque
    Thread

    Value Of A '70 Cj5?

    Found a '70 I think, maybe '71 (flange axles and 225) in a salvage yard. Body is not too bad, missing front fenders and maybe hood, radiator and...
    Thread by: torque, May 14, 2020, 6 replies, in forum: Early CJ5 and CJ6 Tech
  6. torque
    Post

    Dauntless Swap Out

    Wouldn't the flywheel be wrong? odd fire 225, 79-80 Buick even fire.
    Post by: torque, Apr 25, 2020 in forum: Early CJ5 and CJ6 Tech
  7. torque
    Thread

    I Need A 2a Body, Is This A Deal?

    Need a complete body for a cj2A, there are some on E-bay from clintdigger97 for $2700. Is this about the best deal on them?
    Thread by: torque, Oct 23, 2017, 4 replies, in forum: Flat Fender Tech
  8. torque
    Post

    Dana 44 Pinion Seal Issues

    Your 3rd picture is correctly installed and is below flush with the housing, what is the yoke hitting? You say it "interferes with the yoke" do...
    Post by: torque, Sep 18, 2016 in forum: Early CJ5 and CJ6 Tech
  9. torque
    Post

    Yj Spring Swap

    They were not BDS, I think E-bay, don't remember.
    Post by: torque, Sep 13, 2016 in forum: Builds and Fabricators Forum
  10. torque
    Post

    Yj Spring Swap

    I have a '70 cj5 with a cj3A body. Installed 3.5" lift YJ springs (and YJ spring hangers that gained another 1" or so) and also have a 1" body...
    Post by: torque, Sep 13, 2016 in forum: Builds and Fabricators Forum
  11. torque
    Thread

    Hydraulic Clutch Fixed!

    Chevy engine, Ford T18 with Ford clutch disk in Chevy pressure plate. 1980 Jeep master cyl. Novak 3/4" slave cyl. Could not get the clutch to...
    Thread by: torque, Jul 2, 2016, 1 replies, in forum: Early CJ5 and CJ6 Tech
  12. torque
    Post

    66 Cj5 Won't Go Into Third

    I have seen some of the aftermarket blocker rings that were not machined correctly, the notches for the keys must be perfectly centered on the...
    Post by: torque, Jun 26, 2016 in forum: Early CJ5 and CJ6 Tech
  13. torque
    Post

    What Clutch Disc Do I Need?

    Thanks oldtime, I will try that.
    Post by: torque, Apr 2, 2016 in forum: Early CJ5 and CJ6 Tech
  14. torque
    Thread

    What Clutch Disc Do I Need?

    Ford T 18 behind a small block Chevy, 10 1/2" clutch. Bought a late Mustang disc but they are thicker than a Chevy disc and the diaphram fingers...
    Thread by: torque, Apr 2, 2016, 4 replies, in forum: Early CJ5 and CJ6 Tech
  15. torque
    Post

    Hydraulic clutch problem

    The pivot to pedal is 13.5" and pivot to push rod is 3.5" so 3.8 ratio, this may be my problem. The slave-push rod-fork setup is all part of the...
    Post by: torque, Mar 7, 2016 in forum: Early CJ5 and CJ6 Tech
  16. torque
    Post

    Hydraulic clutch problem

    Don't think it's 7/8", if I recall it's like .812"
    Post by: torque, Mar 6, 2016 in forum: Early CJ5 and CJ6 Tech
  17. torque
    Thread

    Hydraulic clutch problem

    Just put together a "70 CJ5 with small block Chevy and 11" diaphragm clutch. Has TJ hanging pedals, 80s Jeep master cyl and Novak 3/4" slave...
    Thread by: torque, Mar 6, 2016, 11 replies, in forum: Early CJ5 and CJ6 Tech
  18. torque
    Post

    Dana 44 30 spline

    Thanks, will just go with a 30 spline case.
    Post by: torque, Jan 12, 2016 in forum: Early CJ5 and CJ6 Tech
  19. torque
    Thread

    Dana 44 30 spline

    I have read the 30 spline side gears can not be put in a 19 spline case (or 10 spline). I wondered why? the axle hole too small? the pocket for...
    Thread by: torque, Jan 12, 2016, 2 replies, in forum: Early CJ5 and CJ6 Tech
  20. torque
    Post

    Hanging pedals in a cj2a

    I bought a pedal setup from a Jeep TJ, the arms are spaced farther apart than the YJ and will straddle the column like the original pedals. The YJ...
    Post by: torque, Aug 14, 2015 in forum: Builds and Fabricators Forum
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2
New Posts