1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
  1. one match
    Post

    Front Driveshaft rubbing starter

    I purchased my 1968 Buick V6 powered CJ5 in 1971. It was original then. It had 4 - ΒΌ inch steel plates between the cross member and frame spacing...
    Post by: one match, Feb 9, 2009 in forum: Early CJ5 and CJ6 Tech
  2. one match
    Post

    What should I do for more rock crawling?

    Gregg, I am 55 just for reference. I have been jeepin since1971. Thats when I got my first jeep a 68 Cj5. I wheeled that thing from Washington...
    Post by: one match, Nov 6, 2008 in forum: Early CJ5 and CJ6 Tech
  3. one match
    Post

    Dana 18 rear output flange.

    I agree with all of this mine used to come loose until I installed new lock washers and I used steel self locking nuts. One Match
    Post by: one match, Oct 30, 2008 in forum: Early CJ5 and CJ6 Tech
  4. one match
    Post

    winshield frame q&a

    I suppose any thing is possible. Although without a lot of bogus looking fabrication I do not se how it could be made to work. Essentially the...
    Post by: one match, Oct 30, 2008 in forum: Intermediate CJ-5/6/7/8
  5. one match
    Post

    winshield frame q&a

    Here is a closer look at my 81 with the later windshield. It really is a later windshield. Note that the windshield wiper motor is in the inside...
    Post by: one match, Oct 30, 2008 in forum: Intermediate CJ-5/6/7/8
  6. one match
    Post

    winshield frame q&a

    This pink & green 70 CJ5 (I call it my Barbie jeep) if you notice has a middle to early CJ sort of windshield with the wiper motor at the bottom....
    Post by: one match, Oct 30, 2008 in forum: Intermediate CJ-5/6/7/8
  7. one match
    Post

    Numbers match cj-5 newbie

    If you want to find out more about jeeps and have time to be at a computer go to the cj3b page. You will get lost for days. Jim
    Post by: one match, Oct 8, 2008 in forum: Early CJ5 and CJ6 Tech
  8. one match
    Post

    Roll bars & Other Junk

    Just Like the picture in your AVATAR. The Diagonal bar is straight. It was common Back then for the bar behind the main hoop to have a ninty...
    Post by: one match, Oct 7, 2008 in forum: Early Jeep Restoration and Research
  9. one match
    Post

    Body mount missing?

    I went home and looked at me frame last night. You are right there is no bracket on the outside of the frame. My CJ5 did have a mount there though...
    Post by: one match, Oct 7, 2008 in forum: Early CJ5 and CJ6 Tech
  10. one match
    Post

    Body mount missing?

    Yes a mount is missing. These are Cj3b frames but it shows the mount you are looking for. It goes in the two aft most holes in the first...
    Post by: one match, Oct 6, 2008 in forum: Early CJ5 and CJ6 Tech
  11. one match
    Thread

    Roll bars & Other Junk

    Many jeeps ago and a long ways away Back in 1972 my wife worked at Whitco Automotive in Colorado Springs, Colorado. I at the same time worked...
    Thread by: one match, Oct 6, 2008, 10 replies, in forum: Early Jeep Restoration and Research
  12. one match
    Post

    Odd Fire 231 - 1977

    If you have the engine apart it is real easy to tell if it is an odd fire engine. An odd fires crank shaft rod journals are one. In other words...
    Post by: one match, Oct 3, 2008 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 12 of 12
Search Again
New Posts