1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 3
  1. en480c4
    Post

    Rebuilding "Cream Puff"

    You're a brave, brave man! I had my 5 shipped from SC to avoid that kind of rust. Best of luck... I'm looking forward to following your progress.
    Post by: en480c4, Aug 13, 2007 in forum: Builds and Fabricators Forum
  2. en480c4
    Post

    SSDutch - a 1964 CJ6

    I couldn't have been happier dealing with Dan. He's a pleasure to talk with on the phone, and is very helpful with any and all questions. The...
    Post by: en480c4, Aug 13, 2007 in forum: Builds and Fabricators Forum
  3. en480c4
    Post

    My '62 Rest-Mod

    I ended up tracking down some nice metal wire clamps with rubber surfaces from a FLAPS. I started around 9:30 by capping off the generator and...
    Post by: en480c4, Aug 11, 2007 in forum: Builds and Fabricators Forum
  4. en480c4
    Post

    My '62 Rest-Mod

    Thanks everyone. The new harness arrived yesterday, along with a speedo. So I'll be pecking away at rewiring this over the next week or so....
    Post by: en480c4, Aug 8, 2007 in forum: Builds and Fabricators Forum
  5. en480c4
    Post

    My '62 Rest-Mod

    Well, they finally had a chance to track down the problem, and it turns out it was the condenser. So the JEEP was up and running... Well, for...
    Post by: en480c4, Aug 2, 2007 in forum: Builds and Fabricators Forum
  6. en480c4
    Post

    My '62 Rest-Mod

    This is what's throwing me for a loop... Everything's new. The only thing in the engine compartment that didn't get touched was the engine,...
    Post by: en480c4, Jul 20, 2007 in forum: Builds and Fabricators Forum
  7. en480c4
    Post

    My '62 Rest-Mod

    Thanks! Unfortunately the JEEP is off the road right now. I can't figure out what's wrong, and need to take a step back because throwing parts...
    Post by: en480c4, Jul 20, 2007 in forum: Builds and Fabricators Forum
  8. en480c4
    Post

    My '62 Rest-Mod

    Thanks everyone. It's been inspected and it's all I've driven all week. So far it's been doing great. I should spend some time this weekend...
    Post by: en480c4, Jul 13, 2007 in forum: Builds and Fabricators Forum
  9. en480c4
    Post

    My '62 Rest-Mod

    Well, it tooks some time, but I managed to get the clutch issues worked out. The previous owner had used the throwout bearing carrier from some...
    Post by: en480c4, Jul 7, 2007 in forum: Builds and Fabricators Forum
  10. en480c4
    Post

    Throwout Bearing Issues

    So, quick question. I'm installing the new bearing tomorrow and have a question about adjusting the linkage. I see in the book that it says the...
    Post by: en480c4, Jul 6, 2007 in forum: Early CJ5 and CJ6 Tech
  11. en480c4
    Post

    Throwout Bearing Issues

    Well, I'd be concerned about drilling that tab because it's about an inch further forward from where the actual tab is supposed to be. I think I...
    Post by: en480c4, Jul 1, 2007 in forum: Early CJ5 and CJ6 Tech
  12. en480c4
    Post

    Throwout Bearing Issues

    Here are a few pics of the throwout bearing I have... As far as I can tell, the squared off side of the throwout bearing collar goes on the side...
    Post by: en480c4, Jun 30, 2007 in forum: Early CJ5 and CJ6 Tech
  13. en480c4
    Thread

    Throwout Bearing Issues

    I've searched and searched, and can't seem to figure out what to do. I've fixed this twice, and the clutch linkage still doesn't work...
    Thread by: en480c4, Jun 30, 2007, 8 replies, in forum: Early CJ5 and CJ6 Tech
  14. en480c4
    Post

    My '62 Rest-Mod

    A Meet and Greet would be a lot of fun. As for cleaning up loose ends, there are definitely a few. I need to replace the wheels at some point....
    Post by: en480c4, Jun 28, 2007 in forum: Builds and Fabricators Forum
  15. en480c4
    Post

    My '62 Rest-Mod

    Well, I pulled the drive shafts, pulled the tunnel, dropped the transmission and transfer case, removed the clutch fork, installed the new spring,...
    Post by: en480c4, Jun 26, 2007 in forum: Builds and Fabricators Forum
  16. en480c4
    Post

    My '62 Rest-Mod

    Thanks everyone. I ordered a new spring, clutch fork and cable and they should be here tomorrow. I figured I'd take care of it all at once so I...
    Post by: en480c4, Jun 25, 2007 in forum: Builds and Fabricators Forum
  17. en480c4
    Post

    Will Jeepster Front Sheetmetal Fit on an ECJ5?

    I have a Jeepster hood & grille that I was going to put on my 5, but I chickened out at the last minute and stuck with the original. But there...
    Post by: en480c4, Jun 25, 2007 in forum: Early CJ5 and CJ6 Tech
  18. en480c4
    Post

    My '62 Rest-Mod

    As it turns out, I'm a bit more of an idiot than I thought. I never put the throwout bearing return spring back on, so the clutch fork dropped...
    Post by: en480c4, Jun 24, 2007 in forum: Builds and Fabricators Forum
  19. en480c4
    Post

    My '62 Rest-Mod

    Well, I had a long list to wrap up, but after a great day we managed to get everything done, fire the JEEP up for the first time in 10 months, and...
    Post by: en480c4, Jun 23, 2007 in forum: Builds and Fabricators Forum
  20. en480c4
    Post

    My '62 Rest-Mod

    Thanks everyone. In all fairness I did say I'd have it ready with any luck. Clearly I should have specified with any good luck, because the...
    Post by: en480c4, Jun 17, 2007 in forum: Builds and Fabricators Forum
Showing results 1 to 20 of 57 Next >
Search Again
Page 1 of 3
New Posts