1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 6
  1. Grinsha
    Post

    ford 352 swap practicality?

    There is an early 5 in a shop near my house that has a 360 in it. Next time i drive by i will get pics of it.
    Post by: Grinsha, Oct 2, 2010 in forum: Early CJ5 and CJ6 Tech
  2. Grinsha
    Post

    Looking for Truth about Valve Cover Gaskets!

    I usually glue the gasket to the cover with 3M weatherstrip adhesive ad put a thin layer of rtv on the head side. tighten by hand till the bolts...
    Post by: Grinsha, Jul 29, 2010 in forum: Intermediate CJ-5/6/7/8
  3. Grinsha
    Post

    power steering fc

    Steering in an FC isnt even close to what is in a CJ. I dont think a saginaw box would work. Supposedly a power box from a toyota pickup can...
    Post by: Grinsha, Feb 3, 2010 in forum: Builds and Fabricators Forum
  4. Grinsha
    Post

    automatic with warn OD

    Might not shift very well without the clutch. You will probably have to shift it while stopped. I usualy leave mine in OD all the time. RSN
    Post by: Grinsha, Dec 27, 2009 in forum: Flat Fender Tech
  5. Grinsha
    Post

    need opinions - engine swallowed a nut

    Are there any numbers or identifying marks on the piston? RSN
    Post by: Grinsha, Aug 15, 2009 in forum: Early CJ5 and CJ6 Tech
  6. Grinsha
    Post

    need opinions - engine swallowed a nut

    Had something similar happen to my M38A1. Screw fell out of the bottom plate on the Q-Jet and into one of the cylinders (don't remember which...
    Post by: Grinsha, Aug 10, 2009 in forum: Early CJ5 and CJ6 Tech
  7. Grinsha
    Post

    Zddplus

    I have used that in 4 engines in the last couple months. It is a cam break in aditive. RSN
    Post by: Grinsha, Aug 7, 2009 in forum: Early CJ5 and CJ6 Tech
  8. Grinsha
    Post

    Need help with FC-150 (CJ-5)

    I think a 2.8 v-6 bellhousing will fit. Don't know where you will get a flywheel. Where are you located? RSN
    Post by: Grinsha, Mar 13, 2009 in forum: Early CJ5 and CJ6 Tech
  9. Grinsha
    Post

    what was the original radio

    The radio in my '63 FC170 is a motorola if that helps RSN
    Post by: Grinsha, Dec 13, 2008 in forum: Early Jeep Restoration and Research
  10. Grinsha
    Post

    Balancing Engine

    Your engine will last longer if you have it balanced. Probably wont have any increase in performance.
    Post by: Grinsha, Oct 27, 2008 in forum: Early CJ5 and CJ6 Tech
  11. Grinsha
    Post

    Time to Play "What is it?"

    A Piece of motorcycle chain might make a good upper holder. Just knock one of the pins out and drop a nail through it to keep it secure. Or weld a...
    Post by: Grinsha, Oct 27, 2008 in forum: Builds and Fabricators Forum
  12. Grinsha
    Post

    felpro headgasket part nr

    There are a few on ebay. RSN
    Post by: Grinsha, Sep 11, 2008 in forum: Early CJ5 and CJ6 Tech
  13. Grinsha
    Post

    Scrap metal

    Call the local welding shops. They usually have a big pile of cut off pieces. RSN
    Post by: Grinsha, Sep 6, 2008 in forum: Builds and Fabricators Forum
  14. Grinsha
    Post

    Lookin for winch pix

    My solenoids are in the passenger side box under the bed. I don't like to mount electrics on the front in the weather.
    Post by: Grinsha, Jul 15, 2008 in forum: Intermediate CJ-5/6/7/8
  15. Grinsha
    Post

    Lookin for winch pix

    Probably not what you are looking for but here's mine. http://grinsha.rack111.com/fc170ramsey.htm
    Post by: Grinsha, Jul 12, 2008 in forum: Intermediate CJ-5/6/7/8
  16. Grinsha
    Post

    Winch Question

    I have a set of controls if you need them. Rescued them from the local car crusher. Unfortunately the winch was already gone. RSN
    Post by: Grinsha, Apr 13, 2008 in forum: Intermediate CJ-5/6/7/8
  17. Grinsha
    Post

    Ring & Pinion Set Up Paint

    I have used white lithium grease a few times and it works good.
    Post by: Grinsha, Apr 4, 2008 in forum: Intermediate CJ-5/6/7/8
  18. Grinsha
    Post

    2.3l ford motor swap

    The 2.3 in the '90 ranger is a Mazda engine. Not the same as the one in the Pinto. I have the pinto to T-90 adapter if you need pics. No its not...
    Post by: Grinsha, Mar 31, 2008 in forum: Flat Fender Tech
  19. Grinsha
    Post

    Removing cam bearings from a block

    I have a machine shop remove and install my cam bearings. It takes a special tool to do it and i cant justify buying one. If you find a tool and...
    Post by: Grinsha, Mar 11, 2008 in forum: Early CJ5 and CJ6 Tech
  20. Grinsha
    Post

    Ok To Reusing flywheel bolts?

    You can reuse the bolts. I have been reusing old flywheel and flexplate bolts for years. I have never personally seen a broken flywheel bolt on a...
    Post by: Grinsha, Mar 1, 2008 in forum: Intermediate CJ-5/6/7/8
Showing results 1 to 20 of 106 Next >
Search Again
Page 1 of 6
New Posts