1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 6
  1. MNTrailboss
    Post

    fiberglass body

    Have an AJs tub on mine with the color impregnated gel coat. It's been on my 74 for about 4 years now with major offroading every year -- note...
    Post by: MNTrailboss, May 14, 2007 in forum: Intermediate CJ-5/6/7/8
  2. MNTrailboss
    Post

    lift for 75 cj

    CV shaft might be a big help, but you don't need to spend big bucks. My rear CV shaft comes from a donor Cherokee front shaft. Total cost was...
    Post by: MNTrailboss, Mar 2, 2006 in forum: Intermediate CJ-5/6/7/8
  3. MNTrailboss
    Post

    T18 to Dana 20

    A JEEP T18 will bolt right up. That's my configuration.
    Post by: MNTrailboss, Feb 17, 2006 in forum: Intermediate CJ-5/6/7/8
  4. MNTrailboss
    Post

    What's a good clutch for my jeep?

    I have the Centerforce 1. Works fine, and clutch pressure is even lower than stock -- saves on my left knee. I offroad all the time and have had...
    Post by: MNTrailboss, Feb 7, 2006 in forum: Intermediate CJ-5/6/7/8
  5. MNTrailboss
    Post

    Hood Fitting

    Thanks guys, Sorry for the late replys. Business took me from wintery Minnesota to sunny Costa Rica, where the CJs and FJ-40s litter the...
    Post by: MNTrailboss, Jan 27, 2006 in forum: Intermediate CJ-5/6/7/8
  6. MNTrailboss
    Thread

    Hood Fitting

    I want to hack up a hood to put in some louvers to cool down the engine bay. I've wrapped the exhaust and installed a new radiator but the 360...
    Thread by: MNTrailboss, Jan 22, 2006, 5 replies, in forum: Intermediate CJ-5/6/7/8
  7. MNTrailboss
    Post

    Spring Perch

    Thanks, I'll give 'em a ring and order a pair.
    Post by: MNTrailboss, Oct 26, 2005 in forum: Intermediate CJ-5/6/7/8
  8. MNTrailboss
    Post

    73 CJ5 304v8 Value?

    Rust, dent, smash, scratch free '73 Jeeps with very solid original tubs go for a bit more here in the salt belt of Minnesota. I bet you would...
    Post by: MNTrailboss, Oct 25, 2005 in forum: Intermediate CJ-5/6/7/8
  9. MNTrailboss
    Thread

    Spring Perch

    I found a rear 44 axle that was changed to spring over for the wider wrangler springs. I want to weld on the original spring mounts under the...
    Thread by: MNTrailboss, Oct 24, 2005, 7 replies, in forum: Intermediate CJ-5/6/7/8
  10. MNTrailboss
    Post

    Edelbrock headers

    Not sure what headers on a 304 is gonna do for ya as I've run the stock manifolds on 360s and 401s and they breath plenty fine with a good 2.5"...
    Post by: MNTrailboss, Jul 18, 2005 in forum: Intermediate CJ-5/6/7/8
  11. MNTrailboss
    Post

    Steering Shafts

    Thanks for the feedback.
    Post by: MNTrailboss, Jun 8, 2005 in forum: Intermediate CJ-5/6/7/8
  12. MNTrailboss
    Thread

    Steering Shafts

    Any difference between steering shafts for a '74 manual, to a power setup? I got the power gearbox out of a 79 CJ. Bob
    Thread by: MNTrailboss, Jun 6, 2005, 4 replies, in forum: Intermediate CJ-5/6/7/8
  13. MNTrailboss
    Post

    Shifter Boots

    I made a couple out of leather -- got the leather for free at a local funiture refinishing shop (scrap bin). Made a triangular template out of...
    Post by: MNTrailboss, May 25, 2005 in forum: Builds and Fabricators Forum
  14. MNTrailboss
    Post

    I know, I know, Another Lift question??

    3.25" lift with 360/T18/D20. I bought a front CV shaft out of a front Cherokee in the salvage yard for $11. Cut it down in the garage and...
    Post by: MNTrailboss, May 25, 2005 in forum: Intermediate CJ-5/6/7/8
  15. MNTrailboss
    Post

    New HEI to install, any advice????

    You don't necessarily have to go TDC #1. Just lift the cap and find which plug your rotor is pointing towards (mark it on the outside, replace...
    Post by: MNTrailboss, May 12, 2005 in forum: Intermediate CJ-5/6/7/8
  16. MNTrailboss
    Post

    POR15 Engine paint

    For my intermediate, I picked up some AMC engine paint from American Performance. Looks pretty darn good.
    Post by: MNTrailboss, Apr 24, 2005 in forum: Early Jeep Restoration and Research
  17. MNTrailboss
    Post

    is it a good plan

    The Tera gears (or for way cheaper the D20/18 low conversion) is not a bad way to go. I still have the stock 3:73 gears so I can hit 55 with...
    Post by: MNTrailboss, Apr 24, 2005 in forum: Intermediate CJ-5/6/7/8
  18. MNTrailboss
    Post

    Electronic Ignition 74 CJ5

    I may be banished from the halls of the buy-new-jeep-parts club for saying this, but I've been running a standard points ignition on my '74 for...
    Post by: MNTrailboss, Apr 19, 2005 in forum: Intermediate CJ-5/6/7/8
  19. MNTrailboss
    Post

    POR15 Engine paint

    I've used their exhaust paint. Seems fine, but I only have about 100 hours on the engine.
    Post by: MNTrailboss, Apr 19, 2005 in forum: Early Jeep Restoration and Research
  20. MNTrailboss
    Post

    Lettering on side and tailgate

    <4wd sells the vinyl jeep letters. I have a set on backorder so I can't tell you how accurate they are.. Doesn't look like the font is correct...
    Post by: MNTrailboss, Apr 9, 2005 in forum: Early Jeep Restoration and Research
Showing results 1 to 20 of 104 Next >
Search Again
Page 1 of 6
New Posts