1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 3
  1. billybbean
    Post

    Name that Carb.....please!

    Yup! dang throttle plate shaft was leaking bad on mine. I took him apart machined a couple of o ring grooves on the end of the shaft. Ran for...
    Post by: billybbean, Aug 17, 2011 in forum: Jeepster Commando and Commando Tech
  2. billybbean
    Post

    Name that Carb.....please!

    Had one like that on a 1980 Datsun pickup.
    Post by: billybbean, Aug 15, 2011 in forum: Jeepster Commando and Commando Tech
  3. billybbean
    Post

    Steering wheel removal 1955 CJ 5

    Nothing that I can see. Pretty crafty IMHO. I've had good luck with Kroil as a penetrating oil.
    Post by: billybbean, Jul 26, 2011 in forum: Early CJ5 and CJ6 Tech
  4. billybbean
    Post

    Pertronix air gap tool

    I have an older Sears engine analyzer I use to set the dwell and to check points resistance. Get dwell right and the gap may not be right anyway...
    Post by: billybbean, Jul 25, 2011 in forum: Early CJ5 and CJ6 Tech
  5. billybbean
    Post

    Pertronix air gap tool

    I've never delt with a Pertronix but I know I've been told since I was a kid not to touch points with a metalic feeler gauge so as not to damage them.
    Post by: billybbean, Jul 24, 2011 in forum: Early CJ5 and CJ6 Tech
  6. billybbean
    Post

    225 Engine miss and low oil pressure

    "There's no noticeable smoke but it does smell a bit like unburned gas" Sounds like a carb issue to me. If it sat over the winter the fuel...
    Post by: billybbean, Jul 12, 2011 in forum: Early CJ5 and CJ6 Tech
  7. billybbean
    Post

    Diesel swap

    Swap over to a 225.
    Post by: billybbean, Jul 4, 2011 in forum: Early CJ5 and CJ6 Tech
  8. billybbean
    Post

    225 running rough

    I had the same problem with my 225 in my cj5. It turned out it had a clogged tube in the carb. Left side was just dumping fuel.
    Post by: billybbean, Jul 4, 2011 in forum: Jeepster Commando and Commando Tech
  9. billybbean
    Post

    Rochester 2G rebuild kit, NAPA part number

    Does any one have the NAPA part number for a float in a 2gc?
    Post by: billybbean, Jul 3, 2011 in forum: Early CJ5 and CJ6 Tech
  10. billybbean
    Profile Post

    Thanks for taking the time to post those pics. Take care.

    Thanks for taking the time to post those pics. Take care.
    Profile Post by billybbean for Grenadiers, Jun 28, 2011
  11. billybbean
    Post

    header clearance problems...

    I picked up a 225, it has the Headman headers on it like above. I would like to put them on my 225 I currently have in my Jeep. How much is...
    Post by: billybbean, Jun 26, 2011 in forum: Early CJ5 and CJ6 Tech
  12. billybbean
    Profile Post

    Hey Patrick, I got a set of headers for my 225 recently. Trying to figure out how to put em in....

    Hey Patrick, I got a set of headers for my 225 recently. Trying to figure out how to put em in. I see in your pics you have them on yours. is...
    Profile Post by billybbean for Patrick, Jun 26, 2011
  13. billybbean
    Post

    225 swap to mid 80's 231

    I am going to stick with the 225. I found another 225 close to me. Going to go pick it up this weekend. Should be a fun project. Hopefuly I'll...
    Post by: billybbean, Jun 22, 2011 in forum: Early CJ5 and CJ6 Tech
  14. billybbean
    Post

    225 swap to mid 80's 231

    Thanks Warloch. I've read the info on here about swaping and such here. With the engine being an 80's model I wasn't sure if there had been some...
    Post by: billybbean, Jun 19, 2011 in forum: Early CJ5 and CJ6 Tech
  15. billybbean
    Thread

    225 swap to mid 80's 231

    I have the opportunity to pick up a rebuilt 231. The guy says it's an 82-87 rear wheel drive engine. Would this 231 go in place of my 225 without...
    Thread by: billybbean, Jun 19, 2011, 4 replies, in forum: Early CJ5 and CJ6 Tech
  16. billybbean
    Post

    225 V6 valve stem seals?

    I'm thinking my 225 is in need of new valve stem seals. Any info on part #'s etc.
    Post by: billybbean, Jun 15, 2011 in forum: Early CJ5 and CJ6 Tech
  17. billybbean
    Post

    225 V6 valve stem seals?

    Do you remember where you got your seals from or maybe have a part #?
    Post by: billybbean, Jun 15, 2011 in forum: Early CJ5 and CJ6 Tech
  18. billybbean
    Post

    T-90 vs. T-96

    What about the T90 vs the T98?
    Post by: billybbean, May 30, 2011 in forum: Early CJ5 and CJ6 Tech
  19. billybbean
    Post

    Will a M38 hard top fit a 63 CJ5

    Thanks for the info!
    Post by: billybbean, Jul 31, 2010 in forum: Early CJ5 and CJ6 Tech
  20. billybbean
    Thread

    Will a M38 hard top fit a 63 CJ5

    I tried to do some research on this but some times it's just best to ask. I'mm looking at getting a hard top for my 63 CJ5. I found one off a 52...
    Thread by: billybbean, Jul 31, 2010, 9 replies, in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 55 Next >
Search Again
Page 1 of 3
New Posts