1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results for Query: herm steering

Search Again
Page 1 of 5
  1. Buildflycrash
    Post

    Scott's '66 Continuous Modifications.

    Bolted the hood on and strapped it down. Rode once around the block. The old Herm power steering was good but the Saginaw was very smooth and...
    Post by: Buildflycrash, Jan 28, 2024 in forum: Builds and Fabricators Forum
  2. melvinm
    Post

    Saginaw Power Steering (pics) Please Add Yours!

    Did the radiator clear the steering gear without any modification ?
    Post by: melvinm, Nov 29, 2023 in forum: Builds and Fabricators Forum
  3. Buildflycrash
    Post

    Scott's '66 Continuous Modifications.

    It’s that time of the year again!! Time to roll Althea into the garage for the winter upgrades and maintenance. Here’s the list (more to be added...
    Post by: Buildflycrash, Oct 5, 2023 in forum: Builds and Fabricators Forum
  4. Fresbone
    Post

    67 Cj5 Build Thread By A Rookie

    I made a little progress today. Again, two steps forward, one step back. I got the rear backing plates on and mostly installed the front discs....
    Post by: Fresbone, Mar 16, 2023 in forum: Builds and Fabricators Forum
  5. Justin Mason
    Post

    Oh Boy, Here We Go.. 1970 Cj5 Dauntless Build

    Thanks! Looking into an 11" drum swap for sure. I think Herm sells a full kit, did you go 11" on front and rear?
    Post by: Justin Mason, Dec 16, 2022 in forum: Builds and Fabricators Forum
  6. Big_Rob2020
    Post

    My First Frame Off Restoration

    So yes this champion radiator is for a late 60's dauntless CJ5. It's technically not correct for my '71, but since I used Herm's Ford reverse...
    Post by: Big_Rob2020, Nov 21, 2022 in forum: Builds and Fabricators Forum
  7. Big_Rob2020
    Post

    My First Frame Off Restoration

    The steering column and steering shaft is stock but highly modified, this is Herm the Overdrive Guy's reverse ford power steering gear set up....
    Post by: Big_Rob2020, Jul 7, 2022 in forum: Builds and Fabricators Forum
  8. Big_Rob2020
    Post

    My First Frame Off Restoration

    Its been about 5 months since my last post and I have made some progress in the right direction. I finished all the fab work and installation of...
    Post by: Big_Rob2020, Jun 19, 2022 in forum: Builds and Fabricators Forum
  9. Norcal69
    Post

    My First Frame Off Restoration

    Your jeep looks great! Just a heads up, your power steering mount is the Buick 455 mount. That mount is has been mistakenly bought by many here...
    Post by: Norcal69, Jan 17, 2022 in forum: Builds and Fabricators Forum
  10. Buildflycrash
    Post

    Mechanical Vs Electric Fuel Pump On 225?

    I can personally say the mechanical pump and the Herm mount/Ford gear are VERY tight. I was not able to remove the fuel pump without removing the...
    Post by: Buildflycrash, Oct 18, 2021 in forum: Builds and Fabricators Forum
  11. Buildflycrash
    Post

    What Did You Do To Your Jeep Today?

    No, that’s not all. Going after the looseness in my steering. I took apart the drag link and tie rod. Found the steering gear is not tight on the...
    Post by: Buildflycrash, Oct 9, 2021 in forum: Builds and Fabricators Forum
  12. RVSwisher
    Post

    Mechanical Vs Electric Fuel Pump On 225?

    While installing my Herm Ford Reverse steering box, I have noticed it is very close to my mechanical fuel pump for my Buick225. I am considering...
    Post by: RVSwisher, Sep 29, 2021 in forum: Builds and Fabricators Forum
  13. RVSwisher
    Thread

    Herm Reverse Ford Steering On Cj3b

    I have been working on installing my Herm Reverse Ford steering box on my CJ3B with a NT Dana 30. I ran into a problem with my drag link, but...
    Thread by: RVSwisher, Sep 29, 2021, 1 replies, in forum: Builds and Fabricators Forum
  14. Buildflycrash
    Post

    Replacing A Dana 27 With A Nt Dana 30 In My 1970 Cj5

    I changed to power steering at the same time. I used the Herm kit to keep the steering gear inside the engine compartment. I like the looks of...
    Post by: Buildflycrash, Mar 24, 2021 in forum: Builds and Fabricators Forum
  15. Big_Rob2020
    Post

    My First Frame Off Restoration

    Hey everyone, long time no update. I have gotten everything on the rolling chassis pretty much done. Really I'm stopped until I get a body, For...
    Post by: Big_Rob2020, Feb 28, 2021 in forum: Builds and Fabricators Forum
  16. Big_Rob2020
    Post

    My First Frame Off Restoration

    Update from this weekend- I finished up the emergency brake and installed the companion flange on the T-case. That finishes up the T-case and the...
    Post by: Big_Rob2020, Nov 22, 2020 in forum: Builds and Fabricators Forum
  17. Bigdaddy13
    Post

    Bigdaddy's Socal 1964 Tuxedo Park Resto-mod.

    Well, after a lot of hemming and hawing, I have a solid plan. Gonna havta push out my planned trips in 2022, - need to allow funds to build up...
    Post by: Bigdaddy13, Nov 9, 2020 in forum: Builds and Fabricators Forum
  18. Buildflycrash
    Post

    What Are These Frame Braces?

    Lots of folks have the Herm kit with V6. But maybe not the 4.3 your using. Look for the topic “ post your power steering photos here” I looked...
    Post by: Buildflycrash, Jun 18, 2020 in forum: Builds and Fabricators Forum
  19. 55plowbuggy
    Post

    What Are These Frame Braces?

    Hello All, I am working on blending two cj5's. The frame is from a 1956 and I also have a 1955. I am installing a Chevy 4.3 v6 and power...
    Post by: 55plowbuggy, Jun 18, 2020 in forum: Builds and Fabricators Forum
  20. Bandit
    Post

    Starting In On My 71ish Jeep

    ...choice for me anyway, as this way I can do a saginaw or herm steering conversion easier, will have hanging pedals for the brakes and hydraulic...
    Post by: Bandit, Nov 17, 2019 in forum: Builds and Fabricators Forum
Showing results 1 to 20 of 95 Next >
Search Again
Page 1 of 5
New Posts