1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Warn Od Front Vs Rear Shift

Discussion in 'Early CJ5 and CJ6 Tech' started by FinoCJ, Jun 10, 2022.

  1. Jun 10, 2022
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,625
    This is copied from Herm's site:

    The first Overdrives were built as a front shift (shift shaft comes out to the front of the OD) and were built as 26 tooth units. The 29 tooth came next, also with the front shift. When Dana-Spicer changed the casting of the dana 18 t/f case the front shift shaft would no longer clear the dana 18 case. Warn redesigned the shifting mechanism and designed a rear shift. This rear shift was then used on all 26 and 29 tooth OD’s that were built.

    Does anyone know when Spicer changed the casting of the D18, and thus the rear shift for the OD is required...thanks!
     
    FinoCJ, Jun 10, 2022
    #1
  2. Jun 10, 2022
    Jw60

    Jw60 Cool school 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sedalia MO.
    Joined:
    Apr 8, 2008
    Messages:
    4,789
    The v6 castings and dana 20 that has a larger body won't clear the front shift. I believe your wagon is good but the cj is not.
     
    Jw60, Jun 10, 2022
    #2
    Ol Fogie, FinoCJ and colojeepguy like this.
  3. Jun 10, 2022
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,155
    This. The large hole D18 requires a rear shift OD.
     
    colojeepguy, Jun 10, 2022
    #3
    Ol Fogie and FinoCJ like this.
  4. Jun 10, 2022
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,625
    okay - didn't connect casting change to the large hole/small hole change...thanks
    So what happens when you mate a small hole D18 to an sm465....will the sm465 get in the way of a front shift OD?
     
    FinoCJ, Jun 10, 2022
    #4
  5. Jun 10, 2022
    Jw60

    Jw60 Cool school 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sedalia MO.
    Joined:
    Apr 8, 2008
    Messages:
    4,789
    The dana 18 is deep enough that the transmission won't interfere with the shifter but the linkage will need a long ear to drop down.

    Check out these drivelines with the different overdrives and how the rod attaches.

    http://www.ewillys.com/category/transmissions/page/2/
     
    Jw60, Jun 10, 2022
    #5
    FinoCJ likes this.
  6. Jun 11, 2022
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,625
    Here is the set-up....the front shift should work...but going to have to get creative bending the lower/horizontal portion of the shift linkage...
    [​IMG]
    [​IMG]
     
    FinoCJ, Jun 11, 2022
    #6
    jeepstar likes this.
  7. Jun 11, 2022
    oldtime

    oldtime oldtime

    St. Charles,...
    Joined:
    Aug 14, 2006
    Messages:
    3,478
    Yes front shift warm should work fine with this transfer case and your linkage including the lever pivot bracket must be custom made anyway because of Synchro Mesh transmission.
     
    oldtime, Jun 11, 2022
    #7
    FinoCJ likes this.
New Posts