1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

No Blinkers Anymore.

Discussion in 'Early CJ5 and CJ6 Tech' started by 2500hd, Jul 21, 2020.

  1. Jul 21, 2020
    2500hd

    2500hd Member

    US
    Joined:
    Aug 3, 2019
    Messages:
    50
    Hi my blinkers stopped working. The light doesn't blink on the steering wheel. Also the relay doesn't click.
    What can I do to get it to work?
    Thanks
     
  2. Jul 21, 2020
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,529
    Check for power in, ground at the turn signal lamps. Check for burned out bulbs.
     
  3. Jul 21, 2020
    Jeff Bromberger

    Jeff Bromberger Quarantined in the Garage

    Dallas Metroplex...
    Joined:
    Jun 28, 2019
    Messages:
    202
    Obvious joke - Blinker Fluid is low...

    More seriously - try disconnecting and then reconnecting the plug for the turn signal switch. It's somewhere near the base of the steering column. Mine was swimming in crud and the contacts were badly oxidized...
     
    Alan28 likes this.
  4. Jul 21, 2020
    2500hd

    2500hd Member

    US
    Joined:
    Aug 3, 2019
    Messages:
    50
    OK I will start checking those locations.
    Thanks
     
  5. Jul 21, 2020
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    Turn the blinkers on while messing with the bulbs. If they work... Bad ground at all bulb housing.
     
  6. Jul 21, 2020
    2500hd

    2500hd Member

    US
    Joined:
    Aug 3, 2019
    Messages:
    50
    I just checked and the brake lights are working.
    I will check on more thing tomorrow. Are there any fuses in the dash that I can't see?
    Thanks
     
  7. Jul 22, 2020
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    There's only maybe 3 inline fuses. I can't remember what they're for. The lights run off a circuit breaker at the switch, I doubt that's the problem.
     
  8. Jul 22, 2020
    Rick Whitson

    Rick Whitson Detroit Area 2024 Sponsor 2022 Sponsor

    I live South of...
    Joined:
    Dec 2, 2014
    Messages:
    1,725
    I found that the plug by the heater on the firewall inside the engine compartment that has double Bullet connectors in sleeves to be corroded. once I pulled them apart and cleaned them everything got better on my Jeep. Good Luck
     
  9. Jul 22, 2020
    Walt Couch

    Walt Couch sidehill Cordele, Ga. 2024 Sponsor 2023 Sponsor 2022 Sponsor

    cordele, Ga.
    Joined:
    Mar 29, 2007
    Messages:
    5,916
    The svc manual shows several model diagrams and all of them show fuse going to the flasher. I would start here with test light.
     
    Focker likes this.
  10. Jul 22, 2020
    Fireball

    Fireball Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Pullman, WA
    Joined:
    Feb 9, 2018
    Messages:
    5,627
    I had the opposite problem the other day. Turn signals worked, but no brake lights. Pulling the cover off the turn signal switch and cleaning the brass contacts with a Scotch-brite pad fixed my issue.
     
  11. Jul 22, 2020
    2500hd

    2500hd Member

    US
    Joined:
    Aug 3, 2019
    Messages:
    50
    I put some dielectric grease on the connectors. Next step is to take off the blinker stalk housing and check that.
    What relay is used for the blinker?
    I can barely get my hands on the round shaped relay. The dash isn't removable.
    Thanks
     
    Last edited: Jul 22, 2020
  12. Jul 22, 2020
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    No relays, maybe you're describing the Flasher?
     
  13. Jul 22, 2020
    2500hd

    2500hd Member

    US
    Joined:
    Aug 3, 2019
    Messages:
    50
    Fixed it! Stupid fuse was the issue.
    Of course I started with replaced the flash, cleaned the turn stalk.
    What a pain.
    Thanks
     
    Glenn likes this.
New Posts