1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

No More Holbrook Asymmetrical Springs Ecj-5

Discussion in 'Intermediate CJ-5/6/7/8' started by Dan & Sandy, Jun 20, 2019.

  1. Jun 20, 2019
    Dan & Sandy

    Dan & Sandy New Member

    Florida
    Joined:
    Dec 5, 2018
    Messages:
    4
    We hope this is the correct forum (we don’t post much, but we follow religiously)

    We need help ....

    Sandy & I have a pretty-much stock 1975 CJ5, 304 cu in with a dealer installed “Tuxedo Front Bench Seat”. Kind of a sweet little jeep. About the only upgrades we have on it are some old-school white wagon wheel rims (8” wide) and 31” x 10.5 ProComp A/T tires. She’s running strong and the tires are amazingly quiet. We continue to love the ‘ol jeep (Sandy calls him Moondog .... I swear it’s more her jeep than mine).

    Anyway, the stock 10-leaf spring suspension is breaking my 61-year old back. The springs have always been “stiff” and we’re figuring they’ve work-hardened some over the past 44 years. It’s time to snag some asymmetrical springs. Of course, we researched and Holbrook Speings came out the winner.

    We contacted them and unfortunately they no longer make the suspension kits. Rats.

    Question & we need help:
    Does anybody either know of a good alternative or possibly a “parts jeep” that may have had a Holbrook upgrade in its earlier life? Parts are parts, eh?

    We would like to keep the original look, feel and height as best as we can, meaning can we keep the spring lift as close to stock. One inch lift would be cool, but we like to stock look.

    Bounce back your thoughts and thanks for any advice
    Dan & Sandy Newfang
    Merritt Island, FL
     
  2. Jun 20, 2019
    txtoller

    txtoller Member 2023 Sponsor 2022 Sponsor

    Weatherford, TX
    Joined:
    May 28, 2014
    Messages:
    971
  3. Jun 20, 2019
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,466
    As an owner of two sets of Holbrooks - I will either go YJ or Alcan setups in the future since I can't get these any longer. I have a set of Alcan springs on the Commando - its just not done yet. They are of high quality and if your looking for custom - give them a call.
     
  4. Jun 20, 2019
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    No comment on the springs - I find my BDS springs just fine. Soft tires at low pressure helps.

    The 60/40 bench seat was a factory option for the CJ-5 and CJ-6. Maybe you have something different, but a bench seat was on the option list and available for many years, maybe the whole run.

    Likely better in the Intermediate forum, since your question does not involve a "build" as such. Mods can decide.

    First post - welcome from Boston!
     
  5. Jun 22, 2019
    Dan & Sandy

    Dan & Sandy New Member

    Florida
    Joined:
    Dec 5, 2018
    Messages:
    4
    Apologies for the misplaced forum, you’re “spot in” that this would be more appropriate in the “Intermediate Forum”

    Good lead on the YJ conversion, we’re looking at that

    Now the question: “Over the Axle” or stock, that being “Under the axle”?
     
  6. Jun 22, 2019
    Focker

    Focker That's a terrible idea...What time? Staff Member

    WA
    Joined:
    Aug 18, 2014
    Messages:
    7,540
    No problem....Moved.
     
  7. Jun 22, 2019
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,754
    The seats in a Jeep are an important component in smoothing the ride. Might want to look at alternatives.

    "The only shock absorbers in my Jeep are the passengers..."
     
  8. Jun 22, 2019
    Lockman

    Lockman OK.....Now I Get It . 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Silver Hill,...
    Joined:
    Dec 4, 2018
    Messages:
    2,698
    ' We would like to keep the original look, feel and height as best as we can, meaning can we keep the spring lift as close to stock. One inch lift would be cool, but we like to stock look."
    Reading your aforementioned wish's........Most definitely ' SUA ' :whistle:
     
  9. Jun 22, 2019
    Dan & Sandy

    Dan & Sandy New Member

    Florida
    Joined:
    Dec 5, 2018
    Messages:
    4
    Thanks again to all for the help
     
    Focker likes this.
  10. Jun 23, 2019
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,111
    The Holbrook springs were considerable higher than stock, 3.5" I believe.
     
  11. Jun 23, 2019
    Lockman

    Lockman OK.....Now I Get It . 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Silver Hill,...
    Joined:
    Dec 4, 2018
    Messages:
    2,698
    I changed out mine , on my 1975 CJ5, back to the OEM's , from a shackle that measured 4" center to center. Their 1 1/2 "s shorter than the previous shackles. Lowered my ' Rosie ' about 3/4 " . I've been contemplating removing 1 ) leaf from my 6 ) leaf fronts, too soften the ride & lower it a tad more. Old legs aren't what the used to be ! ;) ;)
     
    Last edited: Jun 23, 2019
  12. Jun 23, 2019
    Tree cutter 08

    Tree cutter 08 Member

    Cleveland ga
    Joined:
    Feb 14, 2019
    Messages:
    111
    My rough country's ride good. I've got a set of stock springs if you want to try another set. They are noticeably softer.
     
  13. Jun 24, 2019
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,529
    Ed and Gary Holbrook sold Holbrook Specialties probably a year or so ago and they no longer specialize in 4x4 stuff. Holbrook springs “May” be available through Richard Imholt at 503-557-8911. The former owner of R&P 4x4 Parts Inc. My understanding is Gary was going to continue having springs built on a build when ordered basis and sell them through Richard. Not sure if this is happening or not.
     
  14. Jun 25, 2019
    Dan & Sandy

    Dan & Sandy New Member

    Florida
    Joined:
    Dec 5, 2018
    Messages:
    4
    Great lead nickmil.

    What we’ve done per this forum thread:
    1) definitely we’ll be performing a SUA mod (thanks Lockman)
    2) we are looking hard at a YJ conversion .... just a little scared about problems with extending the front leaf beyond the current frame anchor point and potential probs with shifting the axle forward past the original OEM specs. This is what we liked about the Holbrook Brother’s setup ... geometry stayed the same.
    3) we sent a note to Alcan Springs asking if they had a “Holbrook-type” setup? Haven’t heard back yet.
    4) Contacted Jeeps Unlimited to see if they had any “junkers” that might have a pre-existing kit in their stock
    5) finally, we’re now going to snag nickmil’s lead and contact Rich Imholt

    Keeping fingers crossed and thanks for the advice, direction and leads (so far) :)
     
New Posts