1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Harbor Freight

Discussion in 'The Tool Shed' started by tarry99, Aug 16, 2016.

  1. Aug 16, 2016
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    Not condoning anything they sell............but at $160 bucks this is really hard to beat! The sale started today and goes through 8/31/16

    I own one and approve of this message!


    [​IMG]
     
  2. Aug 16, 2016
    GeoffreyL

    GeoffreyL Well-Known Member

    moorestown, nj
    Joined:
    Aug 1, 2012
    Messages:
    1,521
    I too have one, and for the money, they are pretty good.
     
  3. Aug 16, 2016
    Alan F

    Alan F Sponsor

    SE TX
    Joined:
    Jun 16, 2015
    Messages:
    168
    I paid about $150 for a knock down engine hoist back in 1982, changed the jack in 1997 for another $70 but it's been a valuable tool. That's a good deal.

    If I hadn't built a small gantry crane with a spreader bar to lift bodies off frames I'd buy that one as a second.
     
    Last edited: Aug 16, 2016
  4. Aug 16, 2016
    Jeepenstein

    Jeepenstein Me like Jeep..

    North Central FL
    Joined:
    Jun 15, 2003
    Messages:
    2,133
    I have one from Jimmy Joe Bobs tools discount freight beer tobacco and hair care products that I have had for many years. I have yet to have an issue. certain things form HF are functional, probably not for daily use but for the hobby guy they work fine.
     
  5. Aug 16, 2016
    Danefraz

    Danefraz Well-Known Member 2023 Sponsor 2022 Sponsor

    Chico CA
    Joined:
    Aug 11, 2012
    Messages:
    2,263
    I too met with that crack dealer in a shady parking lot and had them load that cardboard freight item in my pickup some time ago. It folds up nicely so it gets out of the way.

    Note: the metal wheels are hard on toes that are exposed when in flip-flops when said item rolls over them... other than that, and a minor 'fitting' issue I had when putting mine together (fixed with a welder and a drill), it's a great item, works as designed.
     
    dozerjim and Rich M. like this.
  6. Aug 16, 2016
    aallison

    aallison 74 cj6, 76 cj5. Has anyone seen my screwdriver?

    Green Cove...
    Joined:
    Nov 24, 2006
    Messages:
    1,929
    Had one for a few years. Got an engine leveler for it. Had to fill the hydraulic oil once but it has been great. Highly recommend for occasional use. Works like a charm for lifting a 6 tub on and off a frame.
     
  7. Aug 17, 2016
    69Willys

    69Willys Las Vegas, NV

    Las Vegas, NV
    Joined:
    Nov 11, 2011
    Messages:
    902
    I have one. It works great.
     
  8. Aug 17, 2016
    jasonjp62

    jasonjp62 Member

    Pennsboro WV.
    Joined:
    Aug 15, 2009
    Messages:
    799
    I have one too works great. For occasional use. I do feel the boom is a lil short at times but I have a pretty big bumper on my jeep.
     
    69Willys likes this.
  9. Aug 17, 2016
    montanacj

    montanacj Member

    Joined:
    Jul 11, 2012
    Messages:
    794
    I like mine too. It gets the job done no problem
     
  10. Aug 17, 2016
    sieg

    sieg Sponsor

    bartonville IL
    Joined:
    Sep 12, 2010
    Messages:
    214
    I bought a HFT plasma cutter works great but won't cut 1/2 in steel like they claim
     
  11. Aug 18, 2016
    Jomani

    Jomani New Member

    Joined:
    Jan 1, 2016
    Messages:
    47
    Great for relatively light stuff like Jeep work. I had a friend try and pull a big block Chevy with TH400 trans out of his Blazer and the thing folded in half. It is rated at 2 tons at the shortest setting - maybe could handle a dead lift but not a swinging engine at that weight.
     
  12. Aug 18, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    [​IMG]

    The cheaper it is, the cheaper it is.
     
  13. Aug 18, 2016
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    Yep............pretty evident what happened there..........warnings or instructions ? No matter what the tool is there is always a dummie out there that can break it.
     
  14. Aug 18, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    Even on sale, I can't see paying that price for dangerous junk, and I'm surprised you approve of them.

    I found an American-built collapsible 2-ton unit on CL a few weeks ago for $140 that is constructed of all 3/16" wall tubing and 1/4" plate with all grade 8 hardware.

    The deals are out there if you're patient.
     
  15. Aug 18, 2016
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    Junk? ...............Not really sure I see it that way , but your welcome to your opinion......Plenty of other folks here don't seem to have a problem with them. I just can't see any reason to re-invent the wheel for $160 bucks , when the price is below the cost of the materials........and It does in lifting capacity what it says it will do.

    If I exceed that capacity , will shame on me for not paying attention! .....................just bought another today for my storage.
     
  16. Aug 18, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    I just see it equal to the old, "$5 helmet for a $5 head" adage.

    When using a hoist, I'd rather be swearing at the ground strap I forgot to unbolt than my hand being crushed, or worse.
     
  17. Aug 18, 2016
    tarry99

    tarry99 Member

    Northern California
    Joined:
    Oct 29, 2012
    Messages:
    3,784
    Hey , I hear what your saying...........but lets face it , It's got nothing to do with the Iron or the tools...........It's all about who is steering that stuff around that makes the difference.
     
  18. Aug 18, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    Just a "forinstance"...

    When you are at the max recommended weight at the specified arm setting and said ground strap breaks..., or you are rolling a load across a concrete floor and roll into a crack, or......, and it sends a shock through the lift, I prefer to have a little extra left in the bank.

    I relate the weight rating on a HF lift to the horsepower rating on a shop vac. I'm sure through somebody's math they came up with 5hp from that little motor, but I'm not risking getting crushed with a shop vac. Let them exaggerate all they want.

    Maybe it's just me, but that's not one area I'd look to cut costs.
    To each his own.
     
  19. Aug 18, 2016
    piffey263

    piffey263 Active Member

    Medford, OR
    Joined:
    Oct 16, 2008
    Messages:
    1,214
    Going to try not to dig a hole,

    What you are saying makes sense, however last time I used an engine stand.I stayed well out of the way. I lifted engine, moved back then set the engine down. I will save moving the engine across the floor for a dolly or engine stand.

    I can't justify buying a nicer one, nor do i have the time to build one. Especially if I will only use it once or twice.

    I don't own an hf engine hoist, just their 20 ton press. Needs reinforcement but works fine. :) Also, I have a small tool box from them. If the hoist bothered me that much I would reinforce it. For the price, and some careful thought I would buy one.

    However it's cheaper for me to rent one instead of driving an hour and half to harbor freight store. Other people it would benefit if they use with caution.
     
  20. Aug 18, 2016
    ITLKSEZ

    ITLKSEZ Hope for the best, prepare for the worst

    Liberty Lake, WA
    Joined:
    Aug 13, 2015
    Messages:
    6,656
    Hoists are hard to use at their highest weight rating because the reach is so short.

    Even a 2-ton lift typically only has a 500# rating at full extension. A jeep F-head alone weighs 470#. Pull the trans out with it, and your already over the questionable rating.

    I'm sure they're fine for lightweight work, or if you plan on modifying it.
     
New Posts