1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by EMA

  1. EMA
    Post

    Dana 24 Twin-stick Conversion

    So to understand this.... If I was to "split" this with two levers. One lever would be REAR with High / Low option + Neutral. 2nd Lever would...
    Post by: EMA, Dec 21, 2021 in forum: Builds and Fabricators Forum
  2. EMA
    Post

    Dana 24 Twin-stick Conversion

    I found this but my version was so blurry.... Thank You..! Curious what the pins # 7229 are for..? The 372720-5 Ball and pin...Detent..?
    Post by: EMA, Dec 21, 2021 in forum: Builds and Fabricators Forum
  3. EMA
    Post

    Dana 24 Twin-stick Conversion

    Thanks..! Have sent out messages to these sources. Looking now for a PDF version of the internal parts layout of this case.
    Post by: EMA, Dec 21, 2021 in forum: Builds and Fabricators Forum
  4. EMA
    Post

    Dana 24 Twin-stick Conversion

    Thanks for your input here... ! I have a spare T98, but not a spare D24 to mock this up for "operation". I guess I could put the truck up on...
    Post by: EMA, Dec 18, 2021 in forum: Builds and Fabricators Forum
  5. EMA
    Post

    Dana 24 Twin-stick Conversion

    Yeah... It is in my 58' 3/4T, 4whl, Texas Forestry Truck I put back together back in the early 90's. It is in the background of my Picture there...
    Post by: EMA, Dec 18, 2021 in forum: Builds and Fabricators Forum
  6. EMA
    Thread

    Dana 24 Twin-stick Conversion

    Who makes a good "conversion kit" to convert a Dana 24 to the twin-stick..? I have looked at the OMIX version...Looking for a better quality..?...
    Thread by: EMA, Dec 17, 2021, 11 replies, in forum: Builds and Fabricators Forum
  7. EMA
    Post

    T98 Shift Pattern

    It is not complete though... Need all including the lever handle assembly though. Thanks though..!
    Post by: EMA, Mar 27, 2021 in forum: Early Jeep Restoration and Research
  8. EMA
    Post

    T98 Shift Pattern

    Buildflycrash...Is this a brake assembly for the T-98..?
    Post by: EMA, Mar 26, 2021 in forum: Early Jeep Restoration and Research
  9. EMA
    Post

    T98 Shift Pattern

    Answer to ITLKSEZ.... Can I have some time to think on this..? Appreciate your help greatly..! Answer to FireBall.... Yeah..agreed... Had not...
    Post by: EMA, Mar 26, 2021 in forum: Early Jeep Restoration and Research
  10. EMA
    Post

    T98 Shift Pattern

    One other thought here while I am considering to pull this trans to fix a leaky oil seal on the engine. When I installed this trans... It had a...
    Post by: EMA, Mar 26, 2021 in forum: Early Jeep Restoration and Research
  11. EMA
    Post

    T98 Shift Pattern

    Is the T-18 Tower a bolt-in swap..? I have a spare T-98 in storage that maybe I could just jump on the lathe and modify that one...then just swap...
    Post by: EMA, Mar 26, 2021 in forum: Early Jeep Restoration and Research
  12. EMA
    Post

    T98 Shift Pattern

    The other issue I was wondering about.... On the T-98's... Is there any place in the casting or could be added for provisions of a "back up" switch..?
    Post by: EMA, Mar 26, 2021 in forum: Early Jeep Restoration and Research
  13. EMA
    Post

    T98 Shift Pattern

    Greatly appreciate the help..! Thanks
    Post by: EMA, Mar 26, 2021 in forum: Early Jeep Restoration and Research
  14. EMA
    Post

    T98 Shift Pattern

    Funny you say this about a laser printer.... I am a retired machinist with a shop.... I have been looking at very small desk-type CNC machines in...
    Post by: EMA, Mar 25, 2021 in forum: Early Jeep Restoration and Research
New Posts